Most Relevant Chemical Engineering Project Topics and Materials (Page 11)

Abstract The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel iron for special p2rts. The technological properties passed by the chosen mild steel are;... Continue Reading

ABSTRACT This research work was arrived as the formulation and production of ethanol (ethyl alcohol) from the fermentation of palm wine. A fresh palm wine was ated which was obtained  from Emene in Enugu State.  The characteristics that was tested before and after fermentation were; specific gravity, refractive index and PH value of the... Continue Reading

ABSTRACT Wheelbarrow can be defined as a machine that is used by labourers, farmes, gardeness, and others for transporting loads to heavy by hand it from one place to another. However, materials used for construction purpose are bought in standard sizes wither in long bars or standard sheet sizes.  Moreover, depending on the type to be... Continue Reading

ABSTRACT A project was carried out to produce high quality liquid air refreshner for domestic uses. The project was carried out using the following apparatus. Beakers (250ML), one conical flask, hydrometer, thermometer, two – 5ml of measuring cylinders, one reactor (plastic reactor), stirrer, weighing balance. The chemicals used in the... Continue Reading

ABSTRACT Adhesive is a substance that holds materials together by surface attachment, while wood adhesive is a substance that is used to hold plywood for furniture works. This substance is essential and has universal applications. Thus the aim of this research work is to produce it using cassava starch as a base binder. Starch is also used in... Continue Reading

ABSTRACTS This project was aimed at producing a fine high quality toilet soap at a low cost which will be of used to home and commercial purposes. The toilet soap produced has its major components caustic potash, palm kernel oil (pKo) caustic soda and soda ash. Other additives are perfume, coaming agent, sodium tripotiphosphate (STPP), colour,... Continue Reading

ABSTRACT The production of high quality foam was carried.  The actualization of the production of polyurethane (fibre) foam was made possible by using the components / chemical raw materials such as polyol (polyurethes resin).  TDI (toluene di-Iso-cyanate, methylane chloride (MC)-(CH2CL).  Silicon oil, stannous octoate, calcum carbonate and... Continue Reading

ABSTRACT Studies were conducted to determine the phytochemicasl present in moringa olrifera and Azadrichta indica leaves. Leaves for this work were washed, room dried ground to powder. The ground leave for both sample were soaked in four different solvent; Ethanol, n-Hexane,... Continue Reading

CHAPTER ONE INTRODUCTION 1.1 Background Perfume is a fragrant liquid made from an extract that has been distilled in alcohol and water. Since the beginning of recorded history, humans have attempted to mask or enhance their own odor by using perfume, which emulates nature’s pleasant smells. Many natural and man-made materials have been used to... Continue Reading

ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding, body... Continue Reading

ABSTRACT This project was carried out to ascertain whether the local palm oil met the required standard. The analytical test carried out include the free fatty acid test the acid value, iodine value moisture, content, saponfication value, peroxide value, specific gravity, colour and viscosity. The specific gravity of the oil sample was determined... Continue Reading

ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method. It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated... Continue Reading

ABSTRACT The production and analysis of “Ngu” extract for temperature and water requirement for leaching of casuistic alkali is the basic objective of this project. The production was carried out by using unit operations and also using the female inflorescence of a palm fruit (Eleasis Guineesis) as raw material. The female... Continue Reading

ABSTRACT This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot. In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time. The three major... Continue Reading

ABSTRACT The production of high quality foam was carried. The actualization of the production of polyurethane (fibre) foam was made possible by using the components / chemical raw materials such as polyol (polyurethes resin). TDI (toluene di-Iso-cyanate, methylane chloride (MC)-(CH2CL). Silicon oil, stannous octoate, calcum carbonate and water. As... Continue Reading

ABSTRACT This project was Carrie lent using sub-bituminous coal and crude palm oil. The degree of bleaching of the palm oil was monitored with a spectorphoto meter. The coal was collected in a lump from the mine. It air-chiecl to removed the moisture content and thereafter, size reduced to a small particle size foe effective activation. The... Continue Reading

ABSTRACT A motorized mixer of 200 liters capacity was constructed to have the capability of mixing 200 liters of fluid during operation. The construction of the mixer involves the preliminary measures and calculations on the surface area of the metal sheet. Some basic workshop practices was carried out during the construction such as the marking... Continue Reading

ABSTRACT This project (Construction Of A Simple Size Reduction Machine) It was constructed locally with the use of local materials and tools in I.M.T mechanical Engineering workshop. The various parts of the equipment were constructed separately using mild steel before finally coupled. During the construction, the conveyors and it’s housing... Continue Reading

ABSTRACT The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method. In the process of moulding the pattern was placed in the flask which contained the green... Continue Reading

ABSTRACT The production of the soap was carried out using all the necessary equipments like the reactor, mould, stirrer, hygrometer guage etc. and all the required reagents for soap production in correct proportion. In the production, palm kernel oil (P.K.O) was used instead of tallow or grease. This was because soap produced from grease or tallow... Continue Reading

ABSTRACT The need for an authentic and reliable report relating to the modification of a proto-type air-conditioning unit is inevitable. Many homes and offices use the air conditioner to cool the temperature in their respective homes and offices, so the maintenance of the air conditioner should be a top priority of every individual in order to... Continue Reading

ABSTRACT The project aims to develop a flow process to obtain the optimum temperature and time necessary for the maximum recovery of alkali present in palm inflorescence. On this ground, a preliminary experiment was performed. During this process, both male and female palm inflorescence were compared for maximum alkali production and it was... Continue Reading

ABSTRACT The repair of the fixed bed adsorption column, a product of arm field technical company was carried out for the purpose of bringing the faulty equipment back to its normal operating system. Before this exercise, the equipment was out of operation because of the completely blocked base of the fixed bed column (water column) and the... Continue Reading

ABSTRACT This project was carried out using coal sample from Onyeama coal mine Enugu, Enugu State.Activated coal was produced by carbonizing the coal and activating it using phosphoric acid at a temperature of 5500c. the degree of bleaching of raw palm oil was monitored using spectronic meter through absorbance measurement. The essence was to... Continue Reading

ABSTRACT The refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu. The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use of equipment in the pilot plant, so that student... Continue Reading