Electrical Engineering Project Topics and Materials (Page 10)

The purpose of this experiment was to obtain a basic knowledge on digital electronics and in turn  set the stage to perform the analysis and design of complex digital electronics circuits. It also  served as an opportunity to learn how the motion sensor worked by using it to turn the LED  on/off. This was done by examining results that were... Continue Reading

A temperature sensor is a device that reads the temperature of the surrounding and relays  the temperature either in degrees Celsius or Kelvin. The LM335 temperature sensor (used in the  experiment) gives out the temperature in degrees Celsius. It is calibrated to output the millivolt  voltage reading in proportion to its units of measurement... Continue Reading

Abstract A Mobile Ad-hoc Data Network (MADNET) is a self-configuring, infrastructure-less network of mobile devices (nodes) where nodes communicate with each other using multi-hop wireless links. Node failures and arbitrary movement of nodes at higher node velocity break the routes and lead to the frequent operation of rebuilding routes that... Continue Reading

ABSTRACT This research work on “Modelling and Simulation of Leakage-Induced Pressure drops along oil and gas pipelines tends to develop flow equations that can detect and localize leakages in oil and gas pipelines by modifying the Darcy-weisbach equation for liquid/oil flow, and the Panhandle B equation for natural gas flow in pipelines. These... Continue Reading

The purpose of this project was to build a motion detector. The main components used were the Arduino microcontroller and the PIR sensor. The project also used an LED and a Piezo buzzer to indicate when motion was detected. The group sought to demonstrate the workings of each component as well as how they work together to carry out the task. The... Continue Reading

ABSTRACT This project presents a 40A maximum power point tracking solar charge controller. The MPPT charge controller tries to keep the voltage and the power stable. The MPPT charge controller will harvest more power from the solar array – it will adjust its input voltage to harvest the maximum power from the solar array and then transform this... Continue Reading

ABSTRACT The purpose of this project was to design and develop a Computer Based Testing (CBT) system in order to facilitate the process of conducting e-examinations especially in tertiary institutions. There is a growing need to find an easy and effective way to carryout continuous assessments for the increasing population of students. The CBT... Continue Reading

ABSTRACT The word “vote” means to choose from a list, to elect or to determine. The main goal of voting (in a scenario involving the students of a given tertiary institution), is to come up with student-leaders of the students’ choice.Most tertiary institutions, FUTO not an exception have problems when it comes to voting. Some of the... Continue Reading

ABSTRACT The basic idea deals with detecting the voltage collapse ahead of time to provide the operators a lead time for remedial actions and for possible prevention of blackouts. To detect cases of voltage collapse, pattern recognition in conjunction with power system simulator for engineering (PSSE) program was created and then deployed in... Continue Reading

ABSTRACT This work analysed the current state of power system in Nigeria with emphasis on distribution system using Akwa Ibom Distribution System as a case study. The components of the study system were analyzed. This work adopted the analytical and simulation approach to reliability and stability assessment. Analysing the system the way it is... Continue Reading

As we know, nowadays issues in the  agriculture field are a major concern.  According to the Union Minister of  Agriculture and Farmers Welfare Narendra  Singh Tomar, 5,579 Indian farmers died by  suicide in 2020. There are many conflicting  reasons for farmer suicides which are  mentioned by Activists and scholars but  high debt burdens,... Continue Reading

This project is intended to provide a solution to a company's problem of developing a smart motion detection device  for home and office security applications. The company intends to deploy 100s of these motion detectors throughout the Greater  London Area. As a result, each motion detector will require a low power wide area network (LPWAN)... Continue Reading

Anatomical variation in the human body presents a complex challenge to design a universal antenna for all. The presence of the human body in close proximity to the antenna also presents a challenge as the near field strongly couples with a lossy medium. Other challenges include design of an antenna that is small in size without affecting its... Continue Reading

ABSTRACT  This report contains five chapters, in chapter one, as an introductory part of this project report, contained in chapter, we first define what accident is, the background of the study, that is to say, how the problem started or what prompted us to carry out the project. The problem statement, this is about the challenges we are solving,... Continue Reading

Abstract This project report describes the design and implementation of an Intelligent Voice Controlled Wheel Chair for disabled people. The model utilizes an Arduino Voice Recognition Module interfaced with a high-level 8-Mt AVR Microcontroller to control motorized movements using voice commands. The model provides both a convenient and... Continue Reading

Abstract The utilization of solar energy is most concerned source in energy sector nowadays. The building  integrated photovoltaic solar panels are increasingly constructed in dense urban areas because they brought   many advantages to the society along with energy saving features. However, at the same time, they raise  tensions in capital... Continue Reading

ABSTRACT  With recent advances in wireless technology, users of wireless network now expect quality of service and performance comparable to what is available in fixed networks. The IEEE 802.11e Medium Access Control (MAC) is an emerging supplement to the IEEE 802.11 Wireless Local Area Network (WLAN) standard that supports Quality-of-Service... Continue Reading

ABSTRACT Condition monitoring of Electrical power equipment has attracted considerable attention for years. The aim of this work is to use Fuzzy logic (FL) Tool Box in building a simulation system that will diagnose all kinds of incipient faults, phase to phase fault and overloading in a transformer and monitor its conditions. Current and rate of... Continue Reading

A CMOS biosensor with a folded floating-gate is created to detect charged biochemical molecules. It contains a FET, a control-gate and a sensing area. The floating-gate spans the whole device, allowing the sensing area to be placed on top of the FET, resulting in a decrease of the device's total area. The device is sensitive to the polarity and... Continue Reading

ABSTRACT Web-based health management system for National Health Insurance Scheme is considered in this project work as an online information storage and retrieval internet portal where the stakeholders registered and participating in the National Health Insurance Scheme of the federal ministry of Health will be able to access relevant information... Continue Reading

ABSTRACT An innovative approach to achieving autonomous vehicle navigation through the integration of image processing techniques and the Raspberry Pi platform. The aim is to develop a self-driving system that can analyze real-time images captured by onboard cameras and make informed decisions based on the detected objects and road conditions. By... Continue Reading

ABSTRACT An intercom is a stand-alone voice communications system for use within a building or small collection of buildings, functioning independently of the public telephone network. Intercoms are generally mounted permanently in buildings and vehicles. Intercoms can incorporate connections to public address loudspeaker systems, walkie talkies,... Continue Reading

TABLE OF CONTENTS TITLE PAGE .. ii DEDICATION .. iv ACKNOWLEDGEMENTS . v TABLE OF CONTENTS . vi LIST OF FIGURES . viii ABSTRACT . ………ix CHAPTER ONE .. 1 INTRODUCTION .. 1 1.1              Background to the Study . 1 1.2        The Sun and the nature of light Energy . 3 1.3        Solar lamp . 4 1.4        Solar... Continue Reading

  ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading

ABSTRACT  With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. The purpose of this project is to design and construct A GSM based home automation using AVR. Using GSM networks, in this project a home power control system has been proposed that will act as an... Continue Reading