Mechanical Engineering Project Topics and Materials (Page 4)

ABSTRACT The aim of this project is to design and fabricate a bench shearing machine which can complete favorably with the imported ones. this machine is designed and fabricate, using our cheap and available materials. Some qualities such as durability, reliability and portability are guaranteed. It is functional and can cut or shear a metal of up... Continue Reading

ABSTRACT This Nylon sealing and cutting machine has an added advantage of making 800 sealed bags per hour.  The constructional machines were sourced locally. The machine can cut and seal Nylon at a affordable cost.  The constructional size of 31 cm x 7.5cm x 12.4 which comprises the following component.  The sealing and cutting filament, the... Continue Reading

ABSTRACT This report covers all activities candied out to rehabilitate a faulty refrigerator. First and foremost, we diagnosed the faulty refrigerator using the basic instruments to know the faults. After which we bought the necessary standard items that caused the fault.  We then started work on it by replacing necessary instruments.  We... Continue Reading

ABSTRACTS The fabrication of a pressurized kerosene oven. This project has been fabricated with special economical needs for the small scale baking industries, wholesalers and distributors who import this type of baking oven from outside the country to supply the customers who wish to use it or those that cannot after gas oven can be used in... Continue Reading

ABSTRACT FLUSHING OF THE CONDENSER The refrigerant gas let into the condenser through the compressor and the vacuum pump was connected to the condenser to absorb dirty. REFILLING OF GAS INTO THE COMPRESSOR Gas was refilled into the compressor due to shortage of gas and it was filled inside the charging value and refrigerant. CHANGING OF DRIVER... Continue Reading

ABSTRACT The project is about fabrication of wheel-barrow, which is fabricated in Mechanical Engineering workshop in Institute of Management and Technology, Enugu. The report comprises seven chapters. Chapter one is about the introduction of the wheel. Chapter two is about the literature review, chapter three is about the material selection and... Continue Reading

ABSTRACT  Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet. Precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel.  The shelf... Continue Reading

ABSTRACT This project aims at designing and constructing a book metallic shelf hose capability will be to contain different standard sizes of books at minimum paces. What is taken into consideration in this project are the cost of its production, processes, and maintenance. Other considerable factors are the functional aspect of the... Continue Reading

ABSTRACT In the society at large Technology is fast replacing the crude method of carrying out work and has been making room for employment. Besides, it has also caught the attention of the youths who will prefer to work in a company with technological operations than one with man-power operations. This project can be used to convey materials... Continue Reading

ABSTRACT  Construction of a potable electric operated motor vehicle for long Volvo Bus. In this project involves the knowledge of mechanical engineering workshop technology and engineering material science and strength. This was exactly what we were taught. We contracted the electric car with the actual dimension of long Volvo bus(Ml-) got from... Continue Reading

ABSTRACT  This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used... Continue Reading

PREFACE Our purpose of embarking on the construction of a project of this kind to present a very vivid and understandable fact that if given the necessary supports, that we the youths and engineers in potentials can more this country forward as regards to technical know how. Such a bird eye view right from time immemorial had proved that lot of... Continue Reading

ABSTRACT An electric popcorn machine is machine that is used to popcorn for human consumption. It uses electricity as it sources of energy, transfer it energy, that is used to pop the Corn. Also it has a stirrer, which rotate due to the convection of electrical energy from the source to mechanical energy in the motor, the stirrer tons the corn so... Continue Reading

ABSTRACT Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy. Also studies were he manner of dependence of these parameters on prints impressed  on sheets of varied thickness.  The... Continue Reading

ABSTRACT. A machine for corn Sheller is highly and greatly needed for consistence of usage of corn in local and international levels. With regards to this indispensable need, a corn-shelling machine is designed which operates to remove the corn grains and leaving the cobs intact. In attainment to this design objective and aims, a proper... Continue Reading

ABSTRACT The aim of the project is to construct a domestic grain grinding machine to be powered by electric motor through pulley and belt transmission. The project is to perform mostly blending and grinding on grains e.g beans, maize, melon, millet and such other food crops. In construction of the project, there are various factors that is being... Continue Reading

ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading

ABSTRACT Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spring to make a complete revolution. Also problems that do arise in clocks and... Continue Reading

ABSTRACT The project work “Construction of standard steel cupboard†was constructed at the mechanical workshop. During the construction, various hand and machinery tools (equipment) such as electric welding machine, hammers, guillote, folding machine, spraying machine, milling machine, steel rule, hard saw, center punch, scribbers,... Continue Reading

ABSTRACT The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing... Continue Reading

ABSTRACT The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 – 3 kg/s of steam at a calculated heat load of 152 – 395/S was fabricated. The steam is to reach the heat exchanger from a distillation column at a temperature of 300k. The specification of... Continue Reading

ABSTRACT Propeller agitator is a specialized of various types of substances.  It consists of three basic components which are the shaft, blade and the vessel. In the construction, mild steel was chosen due to it’s inherent properties.  After the procurement, the following constructional operations were carried out which included marking... Continue Reading

ABSTRACT This is an abstract on the construction of a packed distillation column. A packed distillation column is used in the separating process distillation that is the separation of two miscible liquids.  It was constructed by marking out the dimension of the column, condenser, pot, using steel rule scriber, oxyacetylene flame was used for... Continue Reading

ABSTRACT Wheelbarrow is a simple machine, which belong to the second-class lever. This is because the load or resistance is placed between the effort and the fulcrum. It is used in many areas of work to convey loads that are too heavy or bulky to be carried by hand. Wheelbarrow can be used as farm equipment, industrial equipment among others.... Continue Reading

ABSTRACT The constructional project involved the construction of an industrial barrow of standard size was constructed. The process used went across various Engineering practice. These involved the procurement of galvanized steel of 0.00mm to 300mm thickness. Some galvanized steel rods and pipes were also used for the construction.  The... Continue Reading