Most Read Electrical Engineering Project Topics and Materials (Page 20)

ABSTRACT This project report describes the design and construction of an electronic door lock which uses a microcontroller as the main control unit. The project’s objective was to interface this microcontroller with an LCD, keypad and a DC motor. However, programming the PIC chip to perform a task like identifying an authorised user is also... Continue Reading

ABSTRACT The motive of this project is to construct  equipment for deodorizing kerosene, hence the smell of kerosene is totally eradicated. The equipment was constructed with flat sheet plates of a desired standard, the dimension and the truncated parts were coupled and welded in order to fasten the parts together.  The material was selected to... Continue Reading

ABSTRACT  In the study of the influence of saliency ratio (L /L ) on the performance of a synchronous reluctance generator (SRG), this project investigates two typical generator rotor designs: Generator with cage and without cage otherwise known as cage and cageless rotor respectively. A special attention had been paid to the possible rotor... Continue Reading

ABSTRACT  This project work covers the design and construction of a robotic arm mechanically capable of 5 Degrees of Freedom. It solves the problem of automatically detecting and picking up objects placed within distances of 10-30cm round the robot base platform. It does this by using a simplified forward and inverse kinematic relation modeled in... Continue Reading

ABSTRACT The aim of this project, the design and implementation of an RF communication link, is to design a communication link between a source and a destination and study the properties of the signal being generated by the source (generator). The area of interest in this work is how the signal suffers limitations like attenuation, interference... Continue Reading

ABSTRACT Microcontroller based automate controller is a project design of a system that is used in operating a gate automatically. The system opens the gate automatically when a human being or car is about to enter a compound or exit a compound. The system works by sensing the light rays from the head lamp of the vehicle. The light ray is sensed... Continue Reading

This project is intended to provide a solution to a company's problem of developing a smart motion detection device  for home and office security applications. The company intends to deploy 100s of these motion detectors throughout the Greater  London Area. As a result, each motion detector will require a low power wide area network (LPWAN)... Continue Reading

TABLE OF CONTENTS Page ABSTRACT ……………………………………………………………………………..iii ACKNOWLEDGEMENTS……..………………………………………………………..iv LIST OF ILLUSTRATIONS………………………………………………………….…vii SECTION 1.... Continue Reading

The purpose of this experiment was to obtain a basic knowledge on digital electronics and in turn  set the stage to perform the analysis and design of complex digital electronics circuits. It also  served as an opportunity to learn how the motion sensor worked by using it to turn the LED  on/off. This was done by examining results that were... Continue Reading

Abstract Following the discovery of Oil in Ghana the upstream industry of the Oil and Gas has received a jumpstart and is augmenting the older and more established midstream and downstream industry. The midstream and downstream industries involve the processes that refine, transport, and distribute oil and other crude products and as economic... Continue Reading

Abstract This paper describes the design and fabrication of an epileptic seizure detection watch for the timely detection of Generalized Tonic-Clonic (GTC) seizures; using skin conductance (SC) signals. The watch’s circuit was designed in EasyEDA and implemented on a Breadboard to showcase the dispatch of a seizure event alert to a phone via a... Continue Reading

ABSTRACT  The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of  any battery charger. However the procedure fro developed... Continue Reading

ABSTRACT This design is aimed at providing a system that has the capability of recharging batteries after use. The design is to incorporate an auto charging cut off circuit that operates when the battery is fully charged to avoid damaging the device and also a low voltage circuit which prevents the system from damage should in case the battery... Continue Reading

ABSTRACT  The project work on construction of loud speaker involves some critical research and study concerned electromagnetic induction effect in transducers like loud speaker and its associated parameter required to chose a very good one this parameters are the power rating of loud speaker and the coil. The sizes were also put into... Continue Reading

ABSTRACT This study presents the modelling and optimization of a Hybrid Energy System (HES) for GSM Base Transceiver Station (BTS) sites in emerging cities. The aim is to ensure reliable and cost-effective power supply, considering the availability, dynamism and viability of energy sources. Theoretical approach is applied in the modelling,... Continue Reading

INTRODUCTION As the world is developing the need for electronics in human endeavor is now taking a larger scope. With the invention of certain electronics gadgets in our societies today, certain activities become easily handled for example; in communication where the telephone plays a part.  In places where safety are needed an alarm system will... Continue Reading

ABSTRACT The advantage of cellular communication like GSM technology is a potential solution for such remote controlling activities. GSM-SMS technology can be used to control household appliances from remote places. Remotely, the system allows the home owner to monitor and control his house appliances via his mobile phone set by sending commands... Continue Reading

Amplifiers, which are devices that increase the gain of an audio signal, dominate modern audio technologies. In this project, we designed and built an audio amplifier from scratch in order to demonstrate that such a key device can be constructed using basic electrical engineering principles. After performing major circuit calculations by hand, we... Continue Reading

ABSTRACT With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. The purpose of this project is to design and construct A GSM based home automation using AVR. Using GSM networks, in this project a home power control system has been proposed that will act as an embedded... Continue Reading

ABSTRACT  As technological advancement has been on the increase in our society many have fallen in love with technology and world want to have a feel in virtually  to every thing they do. A design has been made in combination of electrical and electronics to change over from one power sources to the other automatically and trip off generation... Continue Reading

 ABSTRACT The design and construction of the House Bell with indicating light system was creative embarked on for the production of a better alarm signals. Meanwhile different measures and steps such as using electric bell, electric bulb, light emitting diode, 1 mm2 their cable, B Amps plug, lamp holder was used to achieve the objective. All the... Continue Reading

TABLE OF CONTENT: CHAPTER ONE INTRODUCTION 1.1     OBJECTIVE OF PROJECT 1.2     JUSTIFICATION OF PROJECT 1.3     SCOPE OF DIAGRAMS IN PROJECT 1.4     BLOCK DIAGRAM OF PROJECT 1.5     PROJECT  REPORT ORGANIZATION CHAPTER TWO LITERATURE REVIEW 2.1     REVIEW OF REMOTE CONTROL SYSTEMS 2.2     DESCRIPTION OF PROJECT  2.3     USE OF... Continue Reading

ABSTRACT This design implementation of this electronic sequential sign post display employs the use of some specialized components. This section of the project introduces the reader to the different section of the project and the components that makes them up. Emphasis are laid on describing the behaviour and operational system of the components... Continue Reading

Abstract The leading cause of child mortality globally is prematurity. These deaths mostly occur due to unavailable or high cost of keeping babies in clinical incubators, which provide controlled environment for premature neonates. The aim of this project is to develop a cheap and portable wireless incubator for premature babies. The project... Continue Reading

ABSTRACT Most organizations are deploying e-business solutions because of its numerous advantages, such as, increased productivity, reduced transactions costs, wider coverage and increased speed to market. The present academic offices in developing countries still use paper-based approach for most of their activities. Data and information are... Continue Reading