Most Relevant Electrical Engineering Project Topics and Materials

Showing 1 - 25 of 530

1) DESIGN AND CONSTRUCTION OF AN INVERTER

ABSTRACT An inverter is an electronic device that converts direct current (DC¬) to alternating current (AC) the converted Ac can be at any required voltage and frequency with the use of appropriate transformers, switching and control circuit. It’s simple put, is an electronic box that makes household... Continue Reading

2) DESIGN AND CONSTRUCTION OF 1000VA AUTOMATIC VOLTAGE REGULATION ;

DESIGN AND CONSTRUCTION OF 1000VA AUTOMATIC VOLTAGE REGULATION ABSTRACT The design and construction of 1000VA Automatic Voltage Regulator is made to power our Electrical and Electronic devices, supplying them with the normal output voltage which ranges from 100V- 240v irrespective of the constant voltage and current fluctuation, failure and... Continue Reading

3) FACTOR AFFECTING POWER OUTAGE IN NIGERIA

ABSTRACT This research work examines the factors affecting power outage in Nigeria. Constants Power supply is the hallmark of a develop economy. Any nation whose energy need is epileptic in supply prolongs her development and risk-losing potential investors. Nigeria with population of over 120 million... Continue Reading

4) CONSTRUCTION OF SMOKE DETECTOR

Abstract A smoke detector is a device that senses smoke typically as an indicator of fire or non- smoking zone.  In order to ensure human safety and safeguard property against fire in both domestic and commercial settings, different solutions for smoke detection have been developed, a comprehensive literature was carried out on smoke detector,... Continue Reading

5) DESIGN AND CONSTRUCTION OF A 12 VOLTS AUTHOMATIC BATTERY CHARGER

ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading

6) DESIGN AND CONSTRUCTION OF A SINGLE PHASE AUTO-TRANSFORMER OF RATING IKVA, 240V/110, 80 12V, 6V

ABSTRACT This project work-up deals on the design and construction of a single phase step down nations fermor, with raking IKVA, 240V/11OV, 80V 12U, 6V. It is a multi-circuit transformer that has one input as the primary and tappins to produce the... Continue Reading

7) THE CONSTRUCTION OF ELECTRONIC DISPLAY BOARD

TABLE OF CONTENTS CONTENTS CHAPTER ONE 1.1 Introduction 1.2 Objective of the project 1.3 Preamble of the project 1.4 Justification of the project 1.5 Scope of the project 1.6 Constraints in the project CHAPTER TWO 2.0 Literature Review 2.1 History of the project 2.2 Terminology of electronics display... Continue Reading

8) DESIGN AND CONSTRUCTION OF SOUND DETECTOR WITH ALARM SYSTEM

ABSTRACT This project is design and construction of a sound detector with alarm system was done primarily to detector sound. It can be use in industrial and domestics. It employ four discreet stages with power supply which power the system. The 1st block is pick up amplifier containing... Continue Reading

9) CONSTRUCTION OF A DIGITAL DISPLAY BOARD

ABSTRACT Electronic Digital message display Board is an electronic gadget that is capable of displaying length of alphanumeric characters, symbols and any form of representation on a matrix of light emitting diodes (LED) scrolling the characters across the screen for information disemination. This project set out to solve the problem of inadequate... Continue Reading

10) HOME CONTROL SWITCH AUTOMATION USING GSM COMMUNICATION

ABSTRACT The advantage of cellular communication like GSM technology is a potential solution for such remote controlling activities. GSM-SMS technology can be used to control household appliances from remote places. Remotely, the system allows the home owner to monitor and control his house... Continue Reading

11) DESIGN AND CONSTRUCTION OF AUTOMATIC EMERGENCY LIGHT

ABSTRACT As the name of the project implies “Automatic Emergency Light” is an electronic system that can provide light during emergency situations i.e when mains (NEPA) supply fails.  This system can provide enough light with full brightness in a given room or office.   The system makes use of white light emitting diodes for the lightings.... Continue Reading

12) DESIGN AND CONSTRUCTION OF A FAN SPEED CONTROL SYSTEM

Abstract This temperature control fan can be controlled using a microcontroller when it detects a certain temperature that has been set. The purpose of this project is to prevent the waste of voltage usage when it is not hot enough for fan to be needed. The temperature control fan has three... Continue Reading

13) CONSTRUCTION OF CAR TOUCH INTRUDER ALARM.

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum... Continue Reading

14) CONSTRUCTION OF A GSM BASED HOME AUTOMATION USING AVR

ABSTRACT With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. The purpose of this project is to design and construct A GSM based home automation using AVR. Using GSM networks, in this project a home power control... Continue Reading

15) DESIGN AND CONSTRUCTION OF AUTOMATIC SOLAR STREET LIGHT

ABSTRACT In this project work, we are mostly concern about building a simple power streetlight which is automatically operated. There are four main components required to build a solar operated streetlight. The solar array, High efficiency D.C lamp section made by transistor, resistors, and the sensor LDR, changes controller which is made up of... Continue Reading

16) DESIGN AND CONSTRUCTION OF AUTOMATIC HAND DRYER WITH TEMPERATURE DISPLAY

ABSTRACT This project work deals on the design and implementation of an automatic hand-dryer with display capable of drying up a wet hand inserted under its vent and goes off automatically as soon as the ands are removed.  The system also incorporates a decimal counting unit that displays the temperature of the blown out air in 0C.  This... Continue Reading

17) DESIGN AND CONSTRUCTION OF ELECTRIC OVEN

ABSTRACT An oven is a heated enclosure for heating, baking or drying. An electric oven is a heating device used to heat materials to high temperature when electric current is passed through a high resistance heating element (coil or plate). Electric ovens can fine their application in many fields and area of discipline like factories, research... Continue Reading

18) DESIGN AND CONSTRUCTION OF 20WATTS WIRELESS PUBLIC ADDRESS SYSTEM

ABSTRACT It has become inevitable that there would be communication and due to the inherent limitation of the human voice, the public address system came to being. A public addressP.A SYSTEMor ”“ is an electronic amplific ,amplifier and loudspeakers, used to reinforce a given... Continue Reading
  • Type:Project
  • ID:ELE0018
  • Pages:118

19) DESIGN AND CONSTRUCTION OF AN AUTOMATIC CHANGEOVER SWITCH

ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading

20) DESIGN AND CONSTRUCTION OF AN AUTOMATIC THREE PHASE SELECTOR.

ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector. In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a practical aspect of the subject and then providing... Continue Reading

21) DESIGN AND CONSTRUCTION OF A SOLAR OPERATED AUTOMATIC STREET LIGHT CONTROL SYSTEM

. ABSTRACT In this project work, we are mostly concern about building a simple power streetlight which is automatically operated. There are four main components required to build a solar operated streetlight. The solar array, High efficiency D.C lamp section made by... Continue Reading

22) CONSTRUCTION OF A MICROCONTROLLER BASED T JUNCTION TRAFFIC LIGHT CONTROLLER

ABSTRACT T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the... Continue Reading

23) CONSTRUCTION OF 2000W AUTOMATIC VOLTAGE REGULATOR

ABSTRACT This project is all about Automatic Voltage Regulator (AVR), and is a circuit that monitors the input voltage at any point and display the regulated voltage level on the analog meter. It is mainly for electrical/electronic system that is delicate to abnormal voltage level. It is usually connected as an intermediary between voltage supply... Continue Reading

24) POWER OUTAGE IN NIGERIA

ABSTRACT This research work examines the factors affecting power outage in Nigeria. Constants Power supply is the hallmark of a develop economy. Any nation whose energy need is epileptic in supply. Prolongs her development and risk-losing potential investors. Nigeria with population of over 12 million people has for the... Continue Reading

25) DESIGN AND CONSTRUCTION OF AN AUTOMATIC THREE PHASE SELECTOR.

ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector. In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a practical aspect of the subject and then providing... Continue Reading
Need help with your Electrical Engineering Project Topic? Click here to request assistnce or reach us on + 234 813 0686 6500
whatsappWhatsApp Us