DEVELOPMENT OF AEROSOL INSECTICIDE

USING LOCAL RAW MATERIALS

ABSTRACT

This research work was carried out on the development of aerosol insecticide using local raw material. This was made possible through careful and through review of some organic substances to obtain their various properties and characteristic under various conditions. The following promised to be active in the formulation of a biodegradable aerosol insecticide which is non toxic and capable of blocking the respiratory ‘mechanics’ of target insects, especially, the mouth sucking insects. The chemical substances are classified according to their sources. They are as follows:-

(A)         The nature local organic compounds;’ they are refenone (an extract from lonchoearpus  nunits or annun) citronellal (an extract from lemon grass) piperinal (a synergist) and solvents for extraction.

(B)         The synthetic local organic compounds; they are DDVP (Dichloro- dimetty , vinyl phosphate, allethrich. Piperinal, simple paraffin, benzaldehyde and perfume.

In the formulation and production of these insecticides, some chemical process were involved such as pulverization (grind), folteration, extraction heating, stiring etc for the purpose of formulation different standard ratios were used. For instance, for natural local organic compound insecticide, the formulation was 60% by volume of rotenone, 30% by volume of citronellal and 10% by volume of the synergist (ie piperinal) and annyl alcohol. For the synthhetic one, the formulation was 0.5% by volume of DDVP, 0.45% by volume of allethrin, 0.35% by volume, 95% by volume of simple paraffin and 3.7% by volume of mixture of  benzaldehyde and perfume.

          In both products, they were found to be effective when tested. But it was found that the  insecticide from synthetic raw materials had better efficiency than the one from natural raw materials.

          From further test and observation, it was found that the insecticides has little or no effect on the environment.

          Finally, the products were stored in a pressurized spray cans for use. Recommendation were made on the proper management of the insects and also conclusions were drawn to that effect.

CHAPTER ONE

INTRODUCTION

          Insecticides are agents, or preparation for destroying insects and related animals by disruption of vital processes through chemical action. To be more precise, insecticides are materials used for the metigation, control or elimination of insects or animals that are detrimental to human health and economy.

          Recent discoveries of new synthetic insecticides led to major advances in insecticide technology. Coupled with development in aerosol biophysics, highly active chemicals can now be effectively applied to target species to give maximum control of insect peste. Armed with these techniques man is able to subdue and control pest of agricultural, veterinary and public health importance.

          Research scientist have developed a range of insecticides formulations, each specifically designed to combat insect pest affecting man’s health, livestock or economy with maximum safety and efficiency.

          Chemically, insecticides may be of organic or inorganic origin. Also they possess different methods of action and could be classified according to these different methods of action such as stomach poisoning, contact poisoning, residual poisoning, system poisoning, fumigants, repellants or attractants. Contact poison insecticides, being the one of most interest, kill following external bodily contact.

The design of an aerosol insecticide should depend on the nature of the target organism. it is possible to design a “general insect” killing aerosol but such product are by their very nature a compromise, and are thus inferior to products specially formulated for use against specific targets. Certain formulations which are extremely effective against flying insects may give poor control of crewing insects and, conversely, crawling insect killing aerosols may have little action against flying insect. Aerosol insecticides used against flying insect are specifically formulated to induce immediate paralysis and knockdown of flies, mosquitoes and wasp ect. Knockdown follows from the paralytic action of an insecticide christened on insect muscles responsible for flight. These insecticides may be applied as a spray if liquid or in suspension, as a dust or as a gas.

          The qualities and performance of aerosol insecticides are largely dependent on the properties of its constitutuents and the ratio of these constitutuents in the final products. Records shows that insecticides were used as long as 1000 B.C. However, they were more  often useless than useful since they were based on legend and superstition rather than on scientific knowledge. The essential property of early insecticides was a disagreeable or dour rather than the toxic or poisonous nature.

          Aerosol insecticides from available local raw materials must meet the present need for a high standard of performance so as to cater satisfactorily for the needs of the society. Besides, the insecticides produced should conform to be amendments in the federal insecticide, fungicides and Rodenticide Act of 1972 and that of the federal environmental protection Agency Act of 1994. The overview of the conformity to the Acts is that the insecticides produced should be effective and environmental friendly.

          The purpose of this work is to seek alternative local inputs for the development, formulation and production of aerosol insecticide, as well as testing of the complete aerosol insecticide that will effectively complete with other aerosol insecticides made from imported raw materials or synthetic raw materials.

  TERMS AND CONDITIONS

Using our service is LEGAL and IS NOT prohibited by any university/college policies

You are allowed to use the original model papers you will receive in the following ways:

1. As a source for additional understanding of the subject

2. As a source for ideas for your own research (if properly referenced)

3. For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase)

4. Direct citing (if referenced properly)

Thank you so much for your respect to the authors copyright.

For more project materials

Log on to www.grossarchive.com

Or call

+2348130686500

+2348093423853