INVESTIGATION INTO THE SUITABILITY OF SAND AND GRAVEL MATERIALS COMMONLY USED IN BUILDING CONSTRUCTION

  • Type: Project
  • Department: Civil Engineering
  • Project ID: CVE0155
  • Access Fee: ₦5,000 ($14)
  • Pages: 25 Pages
  • Format: Microsoft Word
  • Views: 219
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

TABLE OF CONTENT

Title page i

Declaration ii

Certification iii

Dedication iv

Acknowledgement v

Table of contents vi

Abstract vii

CHAPTER ONE

1.0 Introduction 1

1.1 Statement of the problem 1

1.2 Aim and objectives 2

1.2.1 Objectives of the study 2

1.3 Justification of the study 2

1.4 Scope of study 3

1.5 Methodology 3

CHAPTER TWO

2.0 Literature review 4

2.1 Cement 6

2.1.1 Properties of cement 7

2.2 Water 8

2.3 Sand 8

2.4 Granite 9

2.5 Grading of aggregate 9

2.6 mix proportion method 9

CHAPTER THREE

3.0 Research methodology 10

3.1 Mold acquisition 10

3.2 Quantity of materials needed for a concrete cube 10

3.2.1 Procedure uses 13

3.3 Mix design 14

3.3.1 Sorting and mixing procedure 14

3.4 Sieve size analysis 15

3.4.1 Sieve analysis test 15

3.4.2 Preparation for sieve analysis test 16

3.4.2.1 Procedure for sieve analysis test 16

3.5 Concrete slump test 16

3.5.1 Principle of slump test 17

3.5.2 Apparatus 17

3.5.3 Procedure for slump test 17

3.5.4 Limitation of the slump test 18

3.5.5 Differences in standard 18

3.6 Compressive strength test 18

CHAPTER FOUR

4.0 Result and discussion 28

CHAPTER FIVE

5.0 Conclusion and recommendation 32

References 32


ABSTRACT

This report comprises the use of aggregate both fine and coarse aggregate in the production of concrete, these coarse aggregate are strong in compressive strength of concrete. The coarse and fine aggregate that posses both physical and mechanical properties in the production of concrete which in a correct proportion to give desire strength of the concrete. The mixing ratio that was used is 1:2:4 which known as pure mixing and the other ratio is ratio 1:3:6. 1:2:4 gives 1 head pan of cement with 2 head pan of sharp sand or fine aggregate while 4 head pan for coarse aggregate. After the production of the casted cube, curing was carried out. The duration of the curing is 7 days, 14 days, 28 days. After the curing days, compressive strength test was performed to determine the suitability of the sand and gravel materials in the strength of concrete generally used in the building construction. 


INVESTIGATION INTO THE SUITABILITY OF SAND AND GRAVEL MATERIALS COMMONLY USED IN BUILDING CONSTRUCTION
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Civil Engineering
  • Project ID: CVE0155
  • Access Fee: ₦5,000 ($14)
  • Pages: 25 Pages
  • Format: Microsoft Word
  • Views: 219
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Civil Engineering
    Project ID CVE0155
    Fee ₦5,000 ($14)
    No of Pages 25 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT For thousands of years, sand and gravel have been used in the construction of roads and buildings. Today, demand for sand and gravel continues to increase. Mining operators, in conjunction with cognizant resource agencies, must work to ensure that sand mining is conducted in a responsible manner. Excessive in-stream sand-and-gravel mining... Continue Reading
    . Abstract. The paper considers the management of materials on building construction sites. In the study, method of material procurement practice on construction site, factors affecting material management on building construction site as well as causes wastages on construction sites were determined. The study further Suggest measures for... Continue Reading
    ABSTRACT The major purpose of this study was to determine the needs for environmental friendly materials for building construction. The population of the study consisted mostly of big constriction firms in Anambra State that have had more than five years of active construction experience the sample for the study was 10 reputable construction firms... Continue Reading
     . Abstract.  The paper considers the management of materials on building construction sites. In the study, method of material procurement practice on construction site, factors affecting material management on building construction site as well as causes wastages on construction sites were determined. The study further Suggest measures for... Continue Reading
    Abstract The control of materials on construction sites is handled carelessly by planning and purchasing departments, site supervisors and engineers as well as contractor’s organization and this have been posing various problems to contractors in realizing reasonable profit margin. The research centered on the assessment of materials management... Continue Reading
    Table of Contents CHAPTER ONE INTRODUCTION 1.1 BACKGROUND OF THE STUDY The combined building materials are: 1.1.1  HISTORY OF KANO CITY 1.2  PROBLEM STATEMENT 1.3  RESEARCH QUESTIONS 1.4  AIM AND OBJECTIVES 1.5  SCOPE OF THE STUDY 1.6  SIGNIFICANCE OF THE STUDY 1.7  METHODS OF STUDY CHAPTER TWO LITERATURE REVIEW 2.1  DEVELOPMENT AND... Continue Reading
      ABSTRACT The aim of this research is to analyzed and compare the life cycle cost of alternative root covering materials, Zink coat roofing sheet materials, corrugated Asbestos cement roofing materials, concrete decked roof materials, and long span aluminum roofing materials were considered in this research work with the objectives to determine... Continue Reading
    ABSTRACT The building construction industry is very important to the socio-economic development of a nation. It portrays its religions and cultural values as well as the wealth of the nation. In spite of its importance, the construction industry has been regarded as being risky with frequent and high accident rate and Ill-health problems to... Continue Reading
    ABSTRACT This study has evaluated the effectiveness of metallic materials as chill in sand casting of aluminium alloy. Four plates of dimension 165mm x 80mm x10mm were cast using sand mould. Steel, copper and brass chills in form of cylindrical bar of geometry 7mm in diameter and 50mm long were inserted, side by side at regular intervals of 30mm... Continue Reading
    ABSTRACT This study tend to investigate the effect of synthetic and natural moulding sand on casting of flange like component.  In this study FUTA logo was selected to be cast using aluminium metal. The casting was carried out and the result was analysed according to the quality of casting. It was discovered that for large size component using... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us