+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM

  • Type:Project
  • Chapters:5
  • Pages:65
  • Format:Microsoft Word
(Electrical Engineering Project Topics & Materials)

ABSTRACT

The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuitthereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer.

This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.   

                                         TABLE OF CONTENT

   CHAPTER ONE: Introduction                                                                                  1.1    Background of study

1.2       Aims and objectives

    CHAPTER TWO: Literature Review

    CHAPTER THREE: Specification and operation of system component              3.1       Description of NE55 Timer           

3.2       Description of Resistor

3.3       Description of Capacitor

3.4       Description of Diode

3.5       Description of Transformer

3.6       Description of Loud Speaker and Buzzer

3.7       Description of Transistor

3. 8     Description of L.E.D

    CHAPTER FOUR: Operation of system and its circuit and block diagram

4.1       Operation of  

4.2       The circuit diagram

4.3    The block diagram

    CHAPTER FIVE: Construction, Testing and Packaging

5.1    Values of components

5.2    Assembly

5.3    A schematic diagram of the finished work

    CHAPTER SIX: Conclusion and Recommendation

6.1       Conclusion

6.2       Recommendation

6.3       Observations

6.4       Dificulties

6.5      Reference                        

LIST OF SYMBOLS

NAME                                                                     SYMBOLS

Resistor                                                   

Transistor

Diode                                   

Zener diode                                   

Trimmer capacitor                         

Polarized capacitor                         

Unpolarized capacitor                                    

     

Variable capacitor                                                                                      

CHAPTER ONE:  INTRODUCTION

1.1.            Background of the Study

        The first car alarm was a primitive contraption that utilized a bell or horn connected to the drive shaft. It was created by an unnamed Nebraska inventor in June 20th, 1920. It utilizes the drive shaft to operate its own bell or horn signal when the car is properly moved. This is just a little talk on a car alarm but not a car touch intruder alarm which is a modern, more advanced, and more reliable type of car alarm.

        This car touch sensitive alarm project consist of three NE555 timer IC, the first NE555 was wired as monostable  multi-vibrator and the remaining two were wired as tone generator. When the sensor is touch or has contact with human hand perhaps body, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of R4 (10M) and Q1 (transistor) was bias via R3 and this transistor is in such a way that once it was biased it will supply a negative voltage to tone generator thereby making two NE555 timer which was know as (tone generator) to oscillate to make a bell sound through the buzzer. The tone generators are configured as an astable multi-vibrator whose oscillation frequency can be varied with the help of PR1 and PR2. By adjusting the values of PR1 and PR2, modifications on the tone are possible.

The reset button is used to set or open circuit the system back to its initial stage. The system is powered with 12V power supply voltage.

The first chapter of this project is narrating on the introduction, the concept of the system and also the aims and objective. Chapter two is all about literature review. Chapter three talks about specification and operation of system component. Chapter four is operation of system. Chapter five is about construction, testing and packaging. Chapter six is conclusion, observation, recommendation and References.

1.2       AIM AND OBJECTIVE

       The main aim and objective of the design and construction this project is to create a comfort in the minds of vehicle owners or users when their vehicles are parked or stationed anywhere without much fear of car-theft.

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM

Share This

Details

Type Project
Department Electrical Engineering
Project ID ELE0127
Price ₦3,000 ($9)
Chapters 5 Chapters
No of Pages 65 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Electrical Engineering
    Project ID ELE0127
    Price ₦3,000 ($9)
    Chapters 5 Chapters
    No of Pages 65 Pages
    Format Microsoft Word

    Related Works

    CONSTRUCTION OF CAR TOUCH INTRUDER ALARM ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum... Continue Reading
    ABSTRACT The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all  about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of... Continue Reading
    ABSTRACT This project work deals on the Design and Construction of Intruder Detector Alarm System with Direction/Location Displaywhich is capable of detecting intrusion at any location, sound and alarm and display the exact location of the intruder using... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1.          Background of the Study The industrial Electronics has changed the whole field of Engineering and technology is occurring so rapidly, even in developing countries. It is so because newer technologies overcome older ones. After the industrial revolution the world shifted towards the information... Continue Reading
    ABSTRACT This project deals on the design and construction of an intruder detector for home and office use. Security as one of the biggest issues in our world today and we need a system that will be able to monitor our home, offices and industries by using two sensing... Continue Reading
    Abstract               During the invention of security system alarms, in the early 80s technology of system shadow which involves lighten and sensing of objects was at that age found during their experiments using a special material know as light dependent resistor which its family lies in the resistance serials. The development of... Continue Reading
    CHAPTER ONE 1.1             INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respond to gradual charges in brightness to avoid false alarm. The beeper sounds for only a short time to prevent the battery... Continue Reading
    CHAPTER ONE 1.1             INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respond to gradual charges in brightness to avoid false alarm. The beeper sounds for only a short time to prevent the battery... Continue Reading
    ABSTRACT The term “critical point” is sometimes used to denote specifically the vapour-liquid critical point of a material. The vapour-liquid   point denotes the condition above which distinct liquid and gas phases so not exist. The project, the construction of critical temperature measuring instrument is aimed at measuring the critical... Continue Reading
    ABSTRACT This project is design and construction of a sound detector with alarm system was done primarily to detector sound. It can be use in industrial and domestics. It employ four discreet stages with power supply which power the system. The 1st block is pick up amplifier containing... Continue Reading