CONSTRUCTION OF AN INTRUDER ALARM SYSTEM

  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0399
  • Access Fee: ₦5,000 ($14)
  • Pages: 41 Pages
  • Format: Microsoft Word
  • Views: 619
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of today can produce (construct) things that will help the economic and growth in developing this country is technology 
The intruder alarm system uses electric component to achieve the alarm sound, these components are integrated circuit (ICI,) Register, capacitors and speaker which when combined together it give an alarm system that can be used in houses, industry and commercial company. And how it can be operated. This project does a long way to give evidence and show that it can be use in the economic in favour of electronics and its usefulness in our present life days. WE suggest that this our project should be looked into by the school administration to see the possibilities of producing this alarm system in a commercial has been made by so doing we will help encourage our nations policy indigenous technology

TABLE OF CONTENTS
Title Page
 Approval Page
Dedication
Acknowledgement
 Abstract 
Table of Contents 

CHAPTER ONE
1.1Introduction

CHAPTER TWO
2.1Block Diagram Circuit Implementation of Proposal Intruder Alarm Unit
2.2Power Supply Section (Alternating Current)
2.3Rectification
2.4Regulated Power Supply

CHAPTER THREE
3.1Application of 555 Timing Circuit
3.2Monostable or One Short and Astable Mode
3.3Alarm Section
3.4Application 
3.5Audio Amplifier
1.6Amplifier Coupling
1.7Amplifier Section
Complete Circuit

CHAPTER FOUR
4.1Loved Speaker
4.2Basic Moving Coil Loved Speaker

CHAPTER FIVE
5.1Construction of an Intruder Alarm System
5.2System Construction
5.3Function of the Component
5.4Operation of the System

CHAPTER SIX
6.1Recommendation/Conclusion
6.2Conclusion
6.3Reference.

CONSTRUCTION OF AN INTRUDER ALARM SYSTEM
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0399
  • Access Fee: ₦5,000 ($14)
  • Pages: 41 Pages
  • Format: Microsoft Word
  • Views: 619
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Mechanical Engineering
    Project ID MCE0399
    Fee ₦5,000 ($14)
    No of Pages 41 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT This project work deals on the Design and Construction of Intruder Detector Alarm System with Direction/Location Displaywhich is capable of detecting intrusion at any location, sound and alarm and display the exact location of the intruder using... Continue Reading
    ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the... Continue Reading
    ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the... Continue Reading
    ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the... Continue Reading
    CONSTRUCTION OF CAR TOUCH INTRUDER ALARM ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1.          Background of the Study The industrial Electronics has changed the whole field of Engineering and technology is occurring so rapidly, even in developing countries. It is so because newer technologies overcome older ones. After the industrial revolution the world shifted towards the information... Continue Reading
    Abstract: This project is aimed to implement a  system that will automate the security system of a given area. It ensures that  the user is alerted each time an intruder encroaches a secured position in an  area of application through the sounding of alarm.(Siren) More so, information  about the intruder’s position will also be made noticed... Continue Reading
    Abstract               During the invention of security system alarms, in the early 80s technology of system shadow which involves lighten and sensing of objects was at that age found during their experiments using a special material know as light dependent resistor which its family lies in the resistance serials. The development of... Continue Reading
    CHAPTER ONE 1.1             INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respond to gradual charges in brightness to avoid false alarm. The beeper sounds for only a short time to prevent the battery... Continue Reading
    ABSTRACT The term “critical point” is sometimes used to denote specifically the vapour-liquid critical point of a material. The vapour-liquid   point denotes the condition above which distinct liquid and gas phases so not exist. The project, the construction of critical temperature measuring instrument is aimed at measuring the critical... Continue Reading
    Call Us
    whatsappWhatsApp Us