+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

GEAR DESIGN AND TYPES. (7D)

  • Type:Project
  • Pages:20
  • Format:Microsoft Word
(Mechanical Engineering Project Topics & Materials)
INTRODUCTION
Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work:
digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the transmission may be lacking, for example, in a fan the impeller is mounted  directly on the shaft of the electric motor. But in most cases, the transmission is indispensable, to
match the speed of the mover with that of the actuator, to set in motion several actuators from one
mover, or for another reason. For instance, on a big ship a steam turbine is usually used as a mover.
Its rotational speed is several thousands r/min, whereas the speed of the propeller (for better efficiency) should be about 100 r/min. Hence, between the turbine and the propeller shall be a
speed reducer.
On a small motor boat the propeller, with respect to the speed, may be mounted directly on
the shaft of the engine. But the engine is desired to be placed above the water (just to be maintained easily), and the propeller to work should be submerged; so in this case the transmission is needed as well.
A gear is the most common type of transmission; therefore, it is one of the mandatory  subjects when machine elements are discussed. The geometry of gears is well known, and it is not the subject of investigation here. But the analysis of strength and deformations in gears is impractical without some minimal presentation of tooth geometry. This is the theme of the following section. 

GEAR DESIGN AND TYPES. (7D)

Share This

Details

Type Project
Department Mechanical Engineering
Project ID MCE0192
Price ₦3,000 ($9)
No of Pages 20 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Mechanical Engineering
    Project ID MCE0192
    Price ₦3,000 ($9)
    No of Pages 20 Pages
    Format Microsoft Word

    Related Works

    INTRODUCTION Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work: digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the... Continue Reading
    ABSTRACT Soaps are the sodium salts or potassium salts of stearic acids or any other fatty acids. They are prepared by the saponification process, which is, reacting the oil which contain triglycerides with caustic soda (NaOH) to give the soap. However different oils... Continue Reading
    PREFACE This bibliography on information source of types of library in Nigeria, 2004 – 2010 was undertaken as a prerequisite for my graduation. It is aimed at providing student of library science on insight into the material/ resources publish in their field inside Nigeria. The title were collected from Books, Journals, Project, Theses, Bulletin... Continue Reading
    Title page . (A CASE STUDY OF THE FEDERAL UNIVERSITY OF AGRICULTURE UMUDIKE, ABIA STATE) CHAPTER ONE 1.0.    INTRODUCTION Crop production is an integral part of agriculture, the other half is animal production or husbandry. Crop production can either be on a... Continue Reading
    ABSTRACT The antibacterial activity of three type of medicate soap on staphylococcus aureus isolated from wound infections was conducted. Fifty individual with would infection within the age range of 9-73 years were sampled. Swabsticks were... Continue Reading
    ABSTRACT The effect of pesticides, chchlorodipheny trichloroethane (DDY) and Benzene hexaxhoride (BHc) on the microflora of the three types of soil (loamy, clay and sandy soil) was conducted. The serial... Continue Reading
    ABSTRACT The effect of pesticides, chchlorodipheny trichloroethane (DDY) and Benzene hexaxhoride (BHc) on the microflora of the three types of soil (loamy, clay and sandy soil) was conducted. The serial... Continue Reading
    ABSTRACT The antibacterial activity of three type of medicate soap on staphylococcus aureus isolated from wound infections was conducted. Fifty individual with would infection within the age range of 9-73 years were sampled. Swabsticks were used to collect specimens from wound infection. each swabstick was streaked separately over plates of... Continue Reading
    ABSTRACT The effect of pesticides, chchlorodipheny trichloroethane (DDY) and Benzene hexaxhoride (BHc) on the microflora of the three types of soil (loamy, clay and sandy soil) was conducted. The serial... Continue Reading
      ABSTRACT The antibacterial activity of three type of medicate soap on staphylococcus aureus isolated from wound infections was conducted. Fifty individual with would infection within the age range of 9-73 years were sampled. Swabsticks were used to collect specimens from wound infection. each swabstick was streaked separately over plates of... Continue Reading