+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM

  • Type:Project
  • Pages:73
  • Format:Microsoft Word
(Mechanical Engineering Project Topics & Materials)
ABSTRACT

The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuit thereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer. 
This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.    

TABLE OF CONTENT
Title Page 
Certification
Dedication
Acknowledgement 
Abstract 
Table of content 
List of Symbols 
   
CHAPTER ONE: 
Introduction
1.1 Background of study
1.2 Aims and objectives

CHAPTER TWO: 
Literature Review

CHAPTER THREE: 
Specification and operation of system component              
3.1 Description of NE55 Timer      
3.2 Description of Resistor
3.3 Description of Capacitor
3.4 Description of Diode
3.5 Description of Transformer
3.6 Description of Loud Speaker and Buzzer
3.7 Description of Transistor
3.8 Description of L.E.D

CHAPTER FOUR: 
Operation of system and its circuit and block diagram
4.1 Operation of circuit
4.2 The circuit diagram
4.3 The block diagram

CHAPTER FIVE: 
Construction, Testing and Packaging
5.1 Values of components
5.2 Assembly
5.3 A schematic diagram of the finished work

CHAPTER SIX: 
Conclusion and Recommendation
6.1 Conclusion 
6.2 Recommendation 
6.3 Observations 
6.4 Difficulties
6.5 References


CONSTRUCTION OF CAR TOUCH INTRUDER ALARM

Share This

Details

Type Project
Department Mechanical Engineering
Project ID MCE0109
Price ₦3,000 ($9)
No of Pages 73 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Mechanical Engineering
    Project ID MCE0109
    Price ₦3,000 ($9)
    No of Pages 73 Pages
    Format Microsoft Word

    Related Works

    CONSTRUCTION OF CAR TOUCH INTRUDER ALARM ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum... Continue Reading
    ABSTRACT The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all  about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of... Continue Reading
    ABSTRACT This project work deals on the Design and Construction of Intruder Detector Alarm System with Direction/Location Displaywhich is capable of detecting intrusion at any location, sound and alarm and display the exact location of the intruder using... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1.          Background of the Study The industrial Electronics has changed the whole field of Engineering and technology is occurring so rapidly, even in developing countries. It is so because newer technologies overcome older ones. After the industrial revolution the world shifted towards the information... Continue Reading
    ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and... Continue Reading
    ABSTRACT This project deals on the design and construction of an intruder detector for home and office use. Security as one of the biggest issues in our world today and we need a system that will be able to monitor our home, offices and industries by using two sensing... Continue Reading
    Abstract               During the invention of security system alarms, in the early 80s technology of system shadow which involves lighten and sensing of objects was at that age found during their experiments using a special material know as light dependent resistor which its family lies in the resistance serials. The development of... Continue Reading
    ABSTRACT This project the design an construction of fire alarm was carried out with deep intensive and extensive research work my aim and objective in the price of work is to produce a standard device or electronics that will inform the security about a fire outbreak in the company or house for a quick reaction/action. In this project I shade more... Continue Reading
    CHAPTER ONE 1.1             INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respond to gradual charges in brightness to avoid false alarm. The beeper sounds for only a short time to prevent the battery... Continue Reading
    CHAPTER ONE 1.1             INTRODUCTION The light sensitive alarm is an electronic circuit that detects a sudden shadow falling on the light sensor and sounds the bleeper. When this happens, the circuit will respond to gradual charges in brightness to avoid false alarm. The beeper sounds for only a short time to prevent the battery... Continue Reading