+234 813 0686 500
[email protected]

Mechanical Engineering Project Topics & Research Materials (PDF & DOC)

Browse over 420 Mechanical Engineering project topics and complete research materials for B.Sc, HND, ND, and postgraduate students. All topics are well-researched and suitable for Nigerian universities and polytechnics :(Page 14)
Showing 326 - 350 of 420

326) Fabrication Of A Standard Wheelbarrow

The project is about fabrication of wheel-barrow, which is fabricated in Mechanical Engineering workshop in Institute of Management and Technology, Enugu. The report comprises seven chapters. Chapter one is about the introduction of the wheel. Chapter two is about the literature review, chapter three is about the material selection and... Continue Reading

327) Repair And Rehabilitation Of A Faculty Refrigerator

FLUSHING OF THE CONDENSER The refrigerant gas let into the condenser through the compressor and the vacuum pump was connected to the condenser to absorb dirty. REFILLING OF GAS INTO THE COMPRESSOR Gas was refilled into the compressor due to shortage of gas and it was filled inside the charging value and refrigerant. CHANGING OF DRIVER... Continue Reading

328) The Fabrication Of A Pressurized Kerosene Oven

S The fabrication of a pressurized kerosene oven. This project has been fabricated with special economical needs for the small scale baking industries, wholesalers and distributors who import this type of baking oven from outside the country to supply the customers who wish to use it or those that cannot after gas oven can be used in... Continue Reading

329) Repair Of A Faulty Refrigerator In The Mechanical Engineering Department Of The Institute Of Management And Technology, Enugu

This report covers all activities candied out to rehabilitate a faulty refrigerator. First and foremost, we diagnosed the faulty refrigerator using the basic instruments to know the faults. After which we bought the necessary standard items that caused the fault.  We then started work on it by replacing necessary instruments.  We... Continue Reading

330) Report On Construction Of Nylon Sealing And Cutting Machine

This Nylon sealing and cutting machine has an added advantage of making 800 sealed bags per hour. The constructional machines were sourced locally. The machine can cut and seal Nylon at a affordable cost. The constructional size of 31 cm x 7.5cm x 12.4 which comprises the following component. The sealing and cutting filament, the... Continue Reading

331) The Construction And Fabrication Of Bench Shearing Machine

The air of this project is to design and fabricate a bench shearing machine which can complete favorably with the imported ones. this machine is designed and fabricate, using our cheap and available materials. Some qualities such as durability, reliability and portability are guaranteed. It is functional and can cut or shear a metal of up... Continue Reading

332) The Design And Fabrication Of An Electric Popcorn Frying Machine

PREFACE The electrical popcorn machine is a device for preparing especial popcorn for the human consumption. The device in produced to help the masses to be self valiance in this are of down trodden economy. This project work is divided into five chapters, chapter one; the introduction discusses the relevance of the project work, problems it is... Continue Reading

333) Construction Of Propeller Agitator

Propeller agitator is a specialized of various types of substances. It consists of three basic components which are the shaft, blade and the vessel. In the construction, mild steel was chosen due to it’s inherent properties. After the procurement, the following constructional operations were carried out which included marking out,... Continue Reading

334) Construction Of Sheel And Tube Heat Exchanger

The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 – 3 kg/s of steam at a calculated heat load of 152 – 395/S was fabricated. The steam is to reach the heat exchanger from a distillation column at a temperature of 300k. The specification of... Continue Reading

335) The Construction Of Sieve Equipment

The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing... Continue Reading

336) Construction Of Steel Cupboard

The project work “Construction of standard steel cupboard” was constructed at the mechanical workshop. During the construction, various hand and machinery tools (equipment) such as electric welding machine, hammers, guillote, folding machine, spraying machine, milling machine, steel rule, hard saw, center punch, scribbers,... Continue Reading

337) Repair Of Stop Clocks

Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spring to make a complete revolution. Also problems that do arise in clocks and... Continue Reading

338) The Construction And Fabrication Of A Candle Moulding Machine

The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading

339) Construction Of Grain Grinding Machine

The aim of the project is to construct a domestic grain grinding machine to be powered by electric motor through pulley and belt transmission. The project is to perform mostly blending and grinding on grains e.g beans, maize, melon, millet and such other food crops. In construction of the project, there are various factors that is being... Continue Reading

340) The Design And Fabrication Of A Iron Shelling Machine

A machine for corn Sheller is highly and greatly needed for consistence of usage of corn in local and international levels. With regards to this indispensable need, a corn-shelling machine is designed which operates to remove the corn grains and leaving the cobs intact. In attainment to this design objective and aims, a proper... Continue Reading

341) Design And Fabrication Of A Printing I Block Machine

Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print depends on the impressed pressure the working temperature and the gold foil print paper life expectancy. Also studies were he manner of dependence of these parameters on prints impressed on sheets of varied thickness. The... Continue Reading

342) An Electric Pop-corn Machine

An electric popcorn machine is machine that is used to popcorn for human consumption. It uses electricity as it sources of energy, transfer it energy, that is used to pop the Corn. Also it has a stirrer, which rotate due to the convection of electrical energy from the source to mechanical energy in the motor, the stirrer tons the corn so... Continue Reading

343) Bench Shaping Machine

PREFACE Our purpose of embarking on the construction of a project of this kind to present a very vivid and understandable fact that if given the necessary supports, that we the youths and engineers in potentials can more this country forward as regards to technical know how. Such a bird eye view right from time immemorial had proved that lot of... Continue Reading

344) Construction Of A Mobile Refrigerator

This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used in... Continue Reading

345) Automobile Motor Vehicle Construction

This work is an attempt evolve a quicker and easier method of achieving Transportation. This will no doubt save considering human labour and time wasted involved in traditional manual method of transportation. To achieve this, preliminary experiment was first carried out to determine the optimum speed of the motor vehicle. Various design... Continue Reading

346) Design And Construction Of Metallic Bookshelf

Books are used recoding of what is happening or event that has already taken place which can be storing information it is useful and for the information that such books contained not to cost it support to be properly kept and these can be done when those books are kept in a cool dry place and a place free from rodents and insects attacked... Continue Reading

347) Repair And Rehabilitation Of A Faulty Deep Freezer

Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine maintenance were well observed. Also, a minimized maintenance and a highly successful repair was adopted.... Continue Reading

348) The Construction And Fabricated Of A Mobile Deep Freezer

This work on the construction and fabrication of a mobile deep freezer revolves around the concept of refrigeration. The concept of refrigeration revolves around the reverse Carnot cycle. This is a cycle involving isentropic expansion (at the throttling valve), isothermal expansion (at the evaporator), isentropic compression (at the... Continue Reading

349) The Fabrication Of A Single Face Pressurized Kerosene Cooker

This project is concerned with the fabrication of as a single face pressurized kerosene cooker. The report shows the possible way in which the above mentioned can be designed, fabricated and maintained. Its also shows the strength and properties of the materials it is made of. Defects of the equipment can come through inability to... Continue Reading

350) Modeling And Evaluation Of A Passive Flat-plate Solar Collector

This work investigated the variation of top loss heat transfer coefficient with the emittance of the absorber plate, the collector tilt angle and air gap spacing between the absorber plate and the cover plate. The effects of the emittance of the absorber plate, the collector tilt angle and air gap spacing between the plate and the cover... Continue Reading
  • Type:Project
  • ID:MCE0128
  • Pages:157
Cant find your topic in Mechanical Engineering? Reach us on WhatsApp or call +234 813 0686 6500 .
Choosing the right Mechanical Engineering project topic is essential for academic success. GrossArchive remains a trusted platform for students seeking quality project topics and complete research materials across multiple disciplines. Explore the available Mechanical Engineering project topics on GrossArchive and complete your final year project with confidence.

Students researching Mechanical Engineering project topics often explore related areas such as Electrical Engineering project topics, Civil Engineering project topics, Chemical Engineering project topics, Agric Engineering project topics and Physics project topics to broaden their research scope.

Quick Navigation Menu

Gross Archive
23 Agodogba Av, Park View
Ikoyi, Lagos State,
+ 234 813 0686 6500
+234 809 3423 853
[email protected]

Copyright © Gross Archive. All Rights Reserved
Gross Archive Limited:
whatsappWhatsApp Us