ABSTRACT This project is concerned with the fabrication of as a single face pressurized kerosene cooker. The report shows the possible way in which the above mentioned can be designed, fabricated and maintained. Its also shows the strength and properties of the materials it is made of. Defects of the equipment can come through inability to... Continue Reading
ABSTRACT Propeller agitator is a specialized of various types of substances. It consists of three basic components which are the shaft, blade and the vessel. In the construction, mild steel was chosen due to it’s inherent properties. After the procurement, the following constructional operations were carried out which included marking out,... Continue Reading
ABSTRACT The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 – 3 kg/s of steam at a calculated heat load of 152 – 395/S was fabricated. The steam is to reach the heat exchanger from a distillation column at a temperature of 300k. The specification of... Continue Reading
ABSTRACT The project work “Construction of standard steel cupboard†was constructed at the mechanical workshop. During the construction, various hand and machinery tools (equipment) such as electric welding machine, hammers, guillote, folding machine, spraying machine, milling machine, steel rule, hard saw, center punch, scribbers,... Continue Reading
ABSTRACT Stop clocks are devices for indicating time duration for the occurrence of two events after a passage of time. They are usually powered by batteries and they measure time in unit of seconds. Most clocks stop working as a result of the inability of the main spring to make a complete revolution. Also problems that do arise in clocks and... Continue Reading
ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading
ABSTRACT. A machine for corn Sheller is highly and greatly needed for consistence of usage of corn in local and international levels. With regards to this indispensable need, a corn-shelling machine is designed which operates to remove the corn grains and leaving the cobs intact. In attainment to this design objective and aims, a proper... Continue Reading
ABSTRACT An electric popcorn machine is machine that is used to popcorn for human consumption. It uses electricity as it sources of energy, transfer it energy, that is used to pop the Corn. Also it has a stirrer, which rotate due to the convection of electrical energy from the source to mechanical energy in the motor, the stirrer tons the corn so... Continue Reading
PREFACE Our purpose of embarking on the construction of a project of this kind to present a very vivid and understandable fact that if given the necessary supports, that we the youths and engineers in potentials can more this country forward as regards to technical know how. Such a bird eye view right from time immemorial had proved that lot of... Continue Reading
ABSTRACT This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used in... Continue Reading
ABSTRACT Construction of a potable electric operated motor vehicle for long Volvo Bus. In this project involves the knowledge of mechanical engineering workshop technology and engineering material science and strength. This was exactly what we were taught. We contracted the electric car with the actual dimension of long Volvo bus(Ml-) got from the... Continue Reading
ABSTRACT This project aims at designing and constructing a book metallic shelf hose capability will be to contain different standard sizes of books at minimum paces. What is taken into consideration in this project are the cost of its production, processes, and maintenance. Other considerable factors are the functional aspect of the... Continue Reading
ABSTRACT Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet. Precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel. The shelf is... Continue Reading
ABSTRACTS The fabrication of a pressurized kerosene oven. This project has been fabricated with special economical needs for the small scale baking industries, wholesalers and distributors who import this type of baking oven from outside the country to supply the customers who wish to use it or those that cannot after gas oven can be used in... Continue Reading
This project covers a study of the effect of seawater corrosion on 0.34% and 0.36% carbon steel compositions. Two (2) specimens (steel rods) of length 150mm (each) for both steel compositions were obtained. Out of each was gotten four (4) specimens of 10mm length, 10mm diameter and two (2) specimens of 50mm length, 10mm diameter. This yielded a... Continue Reading
ABSTRACT The fabrication of the solar dryer was successful and test were carried out for various performance comparisons such as No-load and Load performance of the dryer and direct sun drying comparison and noticeable differences was noticed in the final moisture content such that the maximum temperature recorded in the drying chamber and solar... Continue Reading
odel with and Without Winglet Altab Hossain a *, Prithvi Raj Arora b , Ataur Rahman c , Abdul Aziz Jaafar b , A.K.M. Parvez Iqbal a a Department of Mechanical Engineering, University Industry Selangor, Jln Timur Tambahan, 45600 Batang Berjuntai, Selangor Darul Ehsan, Malaysia b... Continue Reading
The fast growing and developing population of the world is so busy that instant food noodles are gaining ground for both humans and domestic animals. Incidentally, the machines involved in the production of these food noddle extruders are imported which results in the depletion of our foreign exchange reserve. Consequently, there is a growing need... Continue Reading
ABSTRACT The study explored the prospects and challenges in the informal auto-mechanic sector focusing on auto-mechanics enterprises within the Kumasi Metropolis. Specifically, the study sought to examine the prospects of the auto-mechanic enterprises, examine the challenges facing auto-mechanic enterprises, and the preparedness of auto-mechanics... Continue Reading
By definition, penetrant testing (PT) is the resurgence of a liquid (or a gas) from a discontinuity in which it had previously been introduced during a penetration operation. A logical extension of the visual examination, this method makes it possible to detect discontinuities opened to the surface of the controlled part in the form of colored or... Continue Reading
INTRODUCTION The production of bench shearing machines to reduce, alleviate and probably eliminate suffering, time, money, wastage of material and more especially the need for technological break through and self reliance has been a major concern of the federal government. Metal shearing and shaping has been a tiring problem in the society from... Continue Reading
ABSTRACT This Nylon sealing and cutting machine has an added advantage of making 800 sealed bags per hour. The constructional machines were sourced locally. The machine can cut and seal Nylon at a affordable cost. The constructional size of 31 cm x 7.5cm x 12.4 which comprises the following component. The sealing and cutting filament, the... Continue Reading
ABSTRACT In the society at large Technology is fast replacing the crude method of carrying out work and has been making room for employment. Besides, it has also caught the attention of the youths who will prefer to work in a company with technological operations than one with man-power operations. This project can be used to convey materials... Continue Reading
ABSTRACT This wrote up is a detail of the processes for the physical realization of the design and construction of mobile deep freezer. It is divided into chapters which discussed expensively the practical refrigeration cycle with rull attention given to design factors working principals and choice of material. Also considered were fabrication... Continue Reading
ABSTRACT When it comes to construction projects, landscaping work, and gardening, you need the right kind of equipment to finish tasks speedily and easily. One piece of equipment you would need is a motorised wheelbarrow. This is intended to carry bulky materials and heavy loads. There are a lot of equipments that can be used these days for... Continue Reading