Most Read Electrical Engineering Project Topics and Materials (Page 7)

ABSTRACT The work presented in this thesis explored the potential of using a mix of renewable energy resources (hybrid power systems, HPSs) to generate electricity that meets power needs of mobile base stations at rural areas in Nigeria. The study was based on theoretical mathematical modeling and simulation using the hybrid optimization model for... Continue Reading

ABSTRACT  With advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. The purpose of this project is to design and construct A GSM based home automation using AVR. Using GSM networks, in this project a home power control system has been proposed that will act as an... Continue Reading

ABSTRACT             This project work-up deals on the design and construction of a single phase step down nations fermor, with raking IKVA, 240V/11OV, 80V 12U, 6V. It is a multi-circuit transformer that has one input as the primary and tappins to produce the output (secondary). It is considered as a single coil in series with the... Continue Reading

ABSTRACT This project intended to simplify the description and working principle of FM wireless microphone, which works on a fixed frequency modulation (FM) band. TABLE OF CONTENTS Approval Sheet Title Page Dedication Acknowledgement Abstract CHAPTER ONE 1.0INTRODUCTION 1.1Aim and Objective of Investigation CHAPTER TWO 2.0Transmitter... Continue Reading

The energy generation and power consuming loads at Brass LNG facility located in Brass Island, Bayelsa State Nigeria were analyzed and compared with expected demand changes and means of minimizing cost and greenhouse gas emission were also proffered with wind and solar energy penetration into the overall power mix . The wind and solar hybrid power... Continue Reading

ABSTRACT The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed... Continue Reading

ABSTRACT The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading

ABSTRACT This project as the name implies is chosen, designed and constructed with the intention of transmitting information such as musicals news intertainments programs and soon. And all these that are written above are being transmitted to the atmosphere using an electromagnetic, signal, and this particular project design and construction is... Continue Reading

ABSTRACT Whenever we think of redefined security, we think of coded electrical door lock. It is a microcontroller based security door lock that can be used in homes, offices, laboratories, etc. for more reliable and high fidelity door control system, powered by electrons panel or electromechanical panels. Due to high rate of insecurity, especially... Continue Reading

ABSTRACT With the rapid growth in the rate of acquisition of Three Phase Motor both for home, office or business uses, there is need to consider the type of motor that is needed and acquired for various uses or purpose. This project explain how individual, organization can assemble a complete motor, emphasis is based on the construction of 3hp... Continue Reading

Abstract This paper presents an innovative access control system, based on human detection and path analysis, to reduce false automatic door system actions while increasing the added values for security applications. The proposed system will first ask the visitor for a password... Continue Reading

ABSTRACT This project is about a microcontroller dot matrix system. This information display system is made in such a way that it can attract attention at any time of the day or night because they system flashes out each of the alphabet or words from left to the right end of the display... Continue Reading

ABSTRACT Most industrial and commercial processes are dependent on electrical power. Power failure or outage in general does not promote development in public and private sectors. The investors do not feel secure to come into a country with constant or frequent power failure. This limits the development of industries.In addition there are... Continue Reading

ABSTRACT: This project deals with the design and implementation of a radio controlled car lock with 5-minutes ignition deactivation facility capable of locking a vehicle using a remote control from a distance. The system is designed in two functional units; the transmitter which is an RF handheld remote control, and the receiver units. The... Continue Reading

TABLE OF CONTENTS Title Page Certification Page Acknowledgements Dedication CHAPTER ONE:INTRODUCTION 1.1Definition of Term CHAPTER TWO:TRANSFORMER FUNDAMENTALS CHAPTER THREE:DESCRIPTION OF COMPONENTS 3.1Resistors 3.2Capacitors 3.2.1Types of Capacitor 3.3Semi-Conductor Diode 3.4Transistors 3.4.1Bipolar Transistor 3.5Field Effect Transistor (FET)... Continue Reading

ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading

ABSTRACT This is a technical report presented on the design and construction of an Automatic Phase Selector.           In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a practical aspect of the subject and then providing the argument necessary for a thorough... Continue Reading

ABSTRACT This project as the name implies is chosen, designed and constructed with the intention of transmitting information such as musicals news intertainments programs and soon. And all these that are written above are being transmitted to the atmosphere using an electromagnetic, signal, and this particular project design and construction is... Continue Reading

ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching stages and then... Continue Reading

ABSTRACT This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed. TABLE OF CONTENT... Continue Reading

ABSTRACT Microcontroller based automate controller is a project design of a system that is used in operating a gate automatically. The system opens the gate automatically when a human being or car is about to enter a compound or exit a compound. The system works by sensing the light rays from the head lamp of the vehicle. The light ray is sensed... Continue Reading

ABSTRACT Blender is an electric machine for size reducing soft food or liquid mixture. Blender is some time called liquidizer consists of a glass jar or jug containing a steel blade assembly at the base driven by a small electric motor. Construction of blender was done based on the principle of size of reduction using electric motor as the major... Continue Reading

ABSTRACT The design and construction of the House Bell with indicating light system was creative embarked on for the production of a better alarm signals. Meanwhile different measures and steps such as using electric bell, electric bulb, light emitting diode, 1 mm2 their cable, B Amps plug, lamp holder was used to achieve the objective. All the... Continue Reading

PREFACE The aim of this project is to construct power amplifier. The system is expected to amplify. The major components in the circuit is the integrated circuit (IC JRE with some circuit elements for the normal operation of the circuit. So as to amplifier an output, the general construction dealt with in the chapters. The levels of treatments... Continue Reading

ABSTRACT This project is titled the design and construction of a DC to AC inverter system. It is designed to meet up with the power demand in the offices and in homes in the absence of power supply from the national supply authority, NEPA. In order words the device / item serves as a substitute for NEPA which almost monopolises the power supply to... Continue Reading