Most Read Electrical Engineering Project Topics and Materials (Page 5)

Showing 101 - 125 of 530

101) DESIGN AND IMPLEMENTATION OF A FOUR WAY TRAFFIC LIGHT CONTROL CIRCUIT

ABSTRACT This work has been aimed at efficient means of controlling the traffic effectively for twenty-four hours. As the world is growing technologically more and more vehicles jump into the public road adding to the already existing number. Consequently, more efficient way of controlling the traffics becomes more desirable as compared to the... Continue Reading

102) CONSTRUCTION OF 12V 10A SOLAR CHARGE CONTROLLER FOR SOLAR ENERGY UTILIZATION

Abstract This project work centered on construction of 12V/10A solar charge controller that is needed in photovoltaic system to safely charge regulate and discharge of sealed lead acid battery through DC load. Solar charge controller is devices that regulate solar photovoltaic power and prevent overcharging, over discharging or overflow of current... Continue Reading

103) DESIGN AND CONSTRUCTION OF 25AMPS SINGLE PHASE AUTOMATIC CHANGE OVER

CHAPTER ONE 1.0             INTRODUCTION As the quest for change over on public power supply and stand by generation increase. Engineering have researches deep into the different methods of achieving to both manual and automatic types.           It may not be taken seriously in some places where power supply is up to 90... Continue Reading

104) DESIGN AND CONSTRUCTION OF AN AUTOMATIC THREE PHASE SELECTOR

ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector.         In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a practical aspect of the subject and then providing the argument necessary for a thorough... Continue Reading

105) DESIGN AND CONSTRUCTION OF AC VOLTMETER USING COMPUTER INTERFACE

ABSTRACT Voltage is a fundamental quantity that is important in every phase of electrical engineering from power system to voltage inside VLSI chips. Of The need to measure the output voltage of a supply is very important meanwhile, The voltmeter is an instrument for measuring... Continue Reading

106) DESIGN AND CONSTRUCT A POWER LINE VANDALISM MONITORING SYSTEM USING ELECTRONIC SYSTEM

CHAPTER ONE 1.0 INTRODUCTION This project gives the insight on the design and construction of a transmission power line vandalism detector system. Vandalism means destructive action. It is a hateful and deliberate defacement/destruction of somebody else’s property or national assets like thehigh-voltage transmission power lines, transmission... Continue Reading

107) COMPUTER BASED ANALYSIS OF ELECTRICAL POWER SYSTEM FOR THE PURPOSE OF STABILITY STUDIES

ABSTRACT This report is on stability study in electrical power system. The ability of an electric power system to reestablish the initial state (or one practically identical) after any disturbance manifested as a deviation from the initial parameter values for the system’s operation. The electric power sources in a power system are usually... Continue Reading

108) CONSTRUCTION OF MICROCONTROLLER BASED VEHICLE SPEED ALARM

ABSTRACT The project is based on Construction of microcontroller vehicle speed alarm system which automatically warns the driver by activating a panic alarm which is triggered on when the driver exceeds the speed limit set in the system which also stops the alarm when the speed is reduced... Continue Reading

109) LINE LOSSES MINIMIZATION IN ELECTRICAL POWER NETWORK USING PARTICLE SWARM OPTIMIZATION

ABSTRACT Energy is a basic necessity for the economic development of a nation. There are different forms of energy, but the most important form is the electrical energy. A modern and civilized society is so much dependent on the use of electrical energy. Activities relating to the generation, transmission and distribution of electrical energy have... Continue Reading

110) DESIGN AND CONSTRUCTION OF AUTOMATIC CHANGE OVER SWITCH WITH INDICATOR

ABSTRACT This project work deals on the design and construction of an automatic power changeover that will change/transfer control from MAINS to Gen set and can switch ON/OFF the Gen automatically. The system integrates phase selector in MAINS and changeover to Gen. It is designed in several blocks all combined to from one functional unit. A +5v... Continue Reading

111) DEVELOPMENT OF A POWER MANAGEMENT ALGORITHM FOR ELECTRICAL POWER NETWORK

ABSTRACT This project work is aimed at developing an efficient Algorithm for the management of Electric Power network using fuzzy logic. The fuzzy logic model functions as a system operator in making decision for load shedding and transfer switching. The new technique uses the system data frequency variation, load variation and voltage variation... Continue Reading

112) CONSTRUCTION AND DESIGN OF A 6V RECHARGEABLE LAMP

ABSTRACT Man has been so used to electricity that he cannot do without it. The absence of electricity causes a lot of sadness in our daily lives. Due to this reason I decided to work on a by rechargeable lamp as my project. The project is to see how one can construct a source of high without really generating is from an A.C source. I decided to... Continue Reading

113) CONSTRUCTION OF UNINTERRUPTIBLE POWER SUPPLY

ABSTRACT Uninterruptible power supplies (UPS) are used to provide power when regular utility power is unavailable.  Although they are commonly used for providing power in remote locations or emergencies, this is not because they are the same as auxiliary power units, emergency power units or standby generators. Unlike the aforementioned power... Continue Reading

114) CONSTRUCTION OF POWER OUTAGE ALARM

ABSTRACT This work is a power supply monitoring device that triggers a buzzer when the mains supply cuts off. Thus a diode (bridge rectifier diode) was used to convert the AC voltage to DC voltage and the 240v/12v AC mains power transfer was used with a bridge rectifier for rectification and a 470Nf filter capacitor C1 for the smoothing of the... Continue Reading

115) DESIGN AND CONSTRUCTION OF A METAL DETECTOR

A BSTRACT The project work titled Design and construction of a metal detector. When fully design and implemented would be able to detect any metallic material that is passing or coming close. This function would serve as a security check for dangerous metallic material as an alarm. Going by the sophisticated means of armed rubbers adopt these days... Continue Reading

116) MICROCONTROLLER BASED AUTOMATIC HAND DRYER SYSTEM

ABSTRACT This system “” comprises of many modules which are: The Sensor/Input Unit, Microcontroller Unit and the Output Interface. The sensor detects when the hand approaches the nozzle. Once the approaching hand is detected, the hand dryer produces a very hot to dry the hand as well as... Continue Reading
  • Type:Project
  • ID:ELE0220
  • Pages:104

117) INVESTIGATION AND EVALUATION OF LOCAL LIQUID DIELECTRIC FOR POWER TRANSFORMER INSULATION

ABSTRACT This work investigates and evaluates local liquid dielectric for insulation of power transformers. Considering the importance of transformer insulation the investigation is borne out of the need to develop the capacity for local production of transformer dielectric. Natural esters of vegetables origin have been found to have the suitable... Continue Reading

118) AN IMPROVED FAULT LOCATION ON POWER SYSTEM TRANSMISSION LINES USING FUZZY LOGIC APPROACH

ABSTRACT The problem of Electricity are enormous and can never be treated completely until the fault department (maintenance) are improved upon for urgent and rapid response to line faults. The present protection scheme only isolates the lines in the event of faults, define the fault, but leaves no proper information about the location of the... Continue Reading

119) CONSTRUCTION OF MICRO CONTROLLER BASED T JUNCTION TRAFFIC LIGHT CONTROLLER

ABSTRACT  T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the pedestrians a right of the way at intervals rather than being struck down when in a... Continue Reading

120) CONSTRUCTION OF METAL DETECTOR

ABSTRACT Metal detectors are electronics sensors that indicate the presence of metallic object without making physical contact with object. They are effective and useful security tools employed in strategic places such as airport, bank, stadiums, government houses and also in production industries to detect presence of metallic object on person... Continue Reading

121) DESIGN AND CONSTRUCTION OF A FOUR WAY TRAFFIC LIGHT CONTROL

ABSTRACT A traffic light also known as a traffic signal, stop light and go light, robot or semaphore is a signally device positioned at four (cross) junction, pedestrian crossing or other locations in other to indicate when it is safe to drive or walk using a universal color code ( and in precise sequence for those that are color blind). Traffic... Continue Reading

122) DESIGN AND CONSTRUCTION OF A 20-M DISTANCE REMOTELY CONTROLLED METAL DETECTOR USING ARDUINO

Abstract The project DESIGN AND CONSTRUCTION OF A 20-METRE DISTANCE REMOTELY CONTROLLED METAL DETECTOR is used for detecting metallic objects such as phones, bombs, and other metallic objects that are hidden from view. The design is based on the principle of the Resonant Frequency Oscillator (RFO) metal detectors in which oscillation is a function... Continue Reading

123) THE IMPACT OF INSURANCE SERVICES IN THE NIGERIAN ECONOMY

ABSTRACT The purpose of this research work was to identify the impact of insurance services in the Nigerian economy. This is because most of Nigerians looks at insurance industry as a weak and poor industry with little or no impact in the Nigerian economy. However, the researcher carefully x-ray the implication of effective contribution of... Continue Reading

124) DESIGN AND CONTRUCTION OF AUTOMATIC PHASE SELECTOR

CHAPTER ONE INTRODUCTION As the growing population of human race widens the gulf between energy supply and energy demand, the imbalance in energy availability sent researchers into excavating for a way of settling this age long squabble. A lasting solution is vested on alternative use of the renewable energy source, a project that is yet to be... Continue Reading

125) DESIGN AND CONSTRUCTION OF VOLTAGE INVERTER SYSTEM WITH TRICKLE CHARGING SYSTEM

ABSTRACT This project is he design and construction of a voltage inverter system with trickle charging system. This device is design to provide power supply for the need of offices, household etc. In absence of NEPA power supply. It would also prevent harm to our appliances caused by power holding company LTD (NEPA) Random power outage . TABLE OF... Continue Reading
Need help with your Electrical Engineering Project Topic? Click here to request assistnce or reach us on + 234 813 0686 6500
whatsappWhatsApp Us