DESIGN AND CONSTRUCTION OF A SPIN DRYER

  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0120
  • Access Fee: ₦5,000 ($14)
  • Pages: 59 Pages
  • Format: Microsoft Word
  • Views: 738
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
This work is aimed at designing and fabricating a spin dryer which can be used in drying spent grains after brewing. This will no doubt save considerable human labours and time wastage involved in conventional method of drying the spent grains by spreading on the ground. It also saves as a means of employments for our teaming population. This machine was designed after due consideration of its ease of production, maintenance and servicing.
Chapter one gives account of the introductory background of the project. Chapter two was the literature review of the project. Chapter three was the synthesis of solution under which different alternatives, comparison of alternatives and choice were discussed. In chapter four, effort was made to discuss the Analysis and Theory of design. The details of construction, Maintenance, Procedures and testing and evaluation were discussed, In chapter five. After the testing, it was found to perform effectively and efficiently. Chapter six became the home for Material evaluation, machine and labour cost analysis. Finally was chapter seven, where we based our discussion on the project, possible recommendations and conclusion.
 
TABLE OF CONTENTS

Title page
Approval page
Release page
Signature page
Dedication
Acknowledgement
Abstract
Table of contents

CHAPTER ONE – INTRODUCTION
1.1 Identification of Needs
1.2 Purpose of Construction
1.3 Importance and Specification of the project
1.4 Scope

CHAPTER TWO – LITERATURE REVIEW
2.1 History about the project
2.2 Introduction of the project

CHAPTER THREE – SYNTHESIS OF SOLUTION
3.1 Different Alternative
3.2 Comparison of Alternatives and Choice

CHAPTER FOUR – THEORY OF DESIGN AND ANALYSIS
4.1 Theory of Design
4.2 Analysis of Design

CHAPTER FIVE – CONSTRUCTION/MAINTENANCE PROCEDURES
5.1 Material Selection
5.2 Production  Processes –Workshop Operational Sequences
5.3 Machining of Components
5.4 Assembly Procedures
5.5 Testing and Evaluation
CHAPTER SIX
6.1 Material Costing Analysis
6.2 Machine Cost Analysis
6.3 Labour Cost Analysis

CHAPTER SEVEN
7.0 Discussion
7.1 Recommendation
7.2 Conclusion
Bibliography
Working Diagram.

DESIGN AND CONSTRUCTION OF A SPIN DRYER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0120
  • Access Fee: ₦5,000 ($14)
  • Pages: 59 Pages
  • Format: Microsoft Word
  • Views: 738
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Mechanical Engineering
    Project ID MCE0120
    Fee ₦5,000 ($14)
    No of Pages 59 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT This project work deals on the design and implementation of an automatic hand-dryer with display capable of drying up a wet hand inserted under its vent and goes off automatically as soon as the ands are removed.  The system also incorporates a decimal counting unit that displays the temperature of the blown out air in 0C.  This... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1       Background of the Study Growth is the irreversible increase in volume (size) number of part, length and weight of an organism (Umeh, 2004). Growth can be defined as a process by which a plant increase in the number and size of leaves and stems (Rayburn, 1993). Growth is also defined as an irreversible change... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1 Background of the Study Growth is the irreversible increase in volume (size) number of part, length and weight of an organism (Umeh, 2004). Growth can be defined as a process by which a plant increase in the number and size of leaves and stems (Rayburn, 1993). Growth is also defined as an irreversible change in the... Continue Reading
    ABSTRACT This study was carried out to generate a design data, design and fabricate a maize corn-on-cob tray dryer used by maize farmers. Ripped maize corns with husks were bought from the market and preserved to retained its moisture content, dehusked and thereafter, dried to a given percentage moisture content of 15%. This was done by laboratory... Continue Reading
    ABSTRACT Drying is out of the major problem in post harvest operation. The traditional method of  Drying (Sun drying) is weather dependent and unhygienic which affect food storage most especially in developing countries like India where more than 3300 to 3700 hours of bright sunshine per year available in North- West and West coastal region. The... Continue Reading
    ABSTRACT A solar dryer integrated with a simple bed rock was designed and constructed with locally available materials to dry tomatoes and pepper. The dryer was composed of solar collector, drying chamber, back up heater and airflow system all integrated together. The back-up heater provided alternative heating during cloudy weather conditions or... Continue Reading
     ABSTRACT A solar dryer integrated with a simple bed rock was designed and constructed with locally available materials to dry tomatoes and pepper. The dryer was composed of solar collector, drying chamber, back up heater and airflow system all integrated together. The back-up heater provided alternative heating during cloudy weather conditions... Continue Reading
    ABSTRACT Spray substance are used to make home grnow powered substance whose particles are usually spherical in shape and approximately 10-40 micro s. The maintenance of pilot plant spray dryer was stated with observation of the faults in the spray dryer. The faulty components were dismantled, serviced and... Continue Reading
    ABSTRACT This project work deals on the design and implementation of an automatic hand-dryer with display capable of drying up a wet hand inserted under its vent and goes off automatically as soon as the ands are removed.  The system also incorporates a decimal counting unit that displays the... Continue Reading
    ABSTRACT This system “” comprises of many modules which are: The Sensor/Input Unit, Microcontroller Unit and the Output Interface. The sensor detects when the hand approaches the nozzle. Once the approaching hand is detected, the hand dryer produces a very hot to dry the hand as well as... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us