CONSTRUCTION OF AN 500W TRANSISTOR AMPLIFIER

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0409
  • Access Fee: ₦5,000 ($14)
  • Pages: 28 Pages
  • Format: Microsoft Word
  • Views: 428
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
The design of this 30 volt Audio Amplifier with volume, table and bass control which was done wit ht he combination of five (5) different circuit which are interconnected during or after construction.  This amplifier operates with an option of a left and right channel.
The combination of these circuit include this main amplifier circuit (which consist of a left and right channel, two treble and bass pre – amp circuit and the power supply circuit.
The main amplifier circuit consist of an interpreter circuit (IC) and lots of resistors, electrolytic capacitor with few a mp circuit of a transistor with some resistors and paper capacitor.
The power circuit which is used to power all the circuit 6f a 30 volt step down transformer, double rectification circuit, with 2 diodes and capacitor (Electrolyic). This amplifier when constructed, can produce up to 800 watts (w) of audio signal.  It can be sued to amplify the sound of audio sound system like mini radio cassette player, compact disc player, turn table  record  player, car radio cassette player or any other sound system that requires increased audio.
This amplifier when produced in large or commercial quality, according to purpose will create job opportunity, provide indigenous electronics technology industry, and it will contribute to economic growth of the nation.

TABLE OF CONTENT
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
INTRODUCTION
TABLE OF CONTENTS

CHAPTER ONE
1.1PREAMBLE
1.2DEFINITION
1.3SPEAKER 

CHAPTER TWO
2.1RESISTOR
2.2CAPACITOR
2.3INTEGRATED CIRCUIT (I.C)
2.4TRANSISTOR
2.5LIGHT EMITTING DIODE
2.6POWER TRANSFORMER

CHAPTER THREE
3.1POWER SUPPLY
3.2OPERATION OF TRANSFORMER
3.3RECTIFICATION AND SMOOTHENING

CHAPTER FOUR
4.1TONE CIRCUIT
4.2TREBLE AND BASS PRE-AMP
4.3OPERATION
4.4DEFINITION OF TERMS

CHAPTER FIVE
5.1AMPLIFIER CIRCUIT
5.2VOLUME CONTROL
5.3BIASING AND STABILIZATION
CHAPTER SIX
6.1OVERALL CIRCUIT DIAGRAM
6.2BLOCK DIAGRAM
COSTING
REFERENCES




CONSTRUCTION OF AN 500W TRANSISTOR AMPLIFIER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0409
  • Access Fee: ₦5,000 ($14)
  • Pages: 28 Pages
  • Format: Microsoft Word
  • Views: 428
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Electrical Engineering
    Project ID ELE0409
    Fee ₦5,000 ($14)
    No of Pages 28 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The design of this 30 volt Audio Amplifier with volume, table and bass control which was done wit ht he combination of five (5) different circuit which are interconnected during or after construction.  This amplifier operates with an option of a left and right channel. The combination of these circuit include this main amplifier circuit... Continue Reading
    PREFACE The aim of this project is to construct power amplifier.  The system is expected to amplify.  The major components in the circuit is the integrated circuit (IC JRE with some circuit elements for the normal operation of the circuit.  So as to amplifier an output, the general construction dealt with in the chapters. The levels of... Continue Reading
    PREFACE The aim of this project is to construct power amplifier. The system is expected to amplify. The major components in the circuit is the integrated circuit (IC JRE with some circuit elements for the normal operation of the circuit. So as to amplifier an output, the general construction dealt with in the chapters. The levels of treatments... Continue Reading
    Amplifiers, which are devices that increase the gain of an audio signal, dominate modern audio technologies. In this project, we designed and built an audio amplifier from scratch in order to demonstrate that such a key device can be constructed using basic electrical engineering principles. After performing major circuit calculations by hand, we... Continue Reading
    ABSTRACT The aim of this project work is to create an alternative sound amplifying circuit that will enable the enhancement of electronic production. This portable RC coupled amplifier constructed with very cheap and locally sourced materials found reliable and effective in function. Thus the... Continue Reading
    ABSTRACT The aim of this project work is to create an alternative sound amplifying circuit that will enable the enhancement of electronic production. This portable RC coupled amplifier constructed with very cheap and locally sourced materials found reliable and effective in function. Thus the... Continue Reading
    ABSTRACT The topic of this project is ' Audio Amplifier'. The research embarked upon this study or project by using both primary and secondary source of data. The main instrument used for data collection are: Modern electronics circuit Design. By David J. Commer. Electronics Devices. By Floyd... Continue Reading
    Amplifiers, which are devices that increase the gain of an audio signal, dominate modern audio technologies. In this project, we designed and built an audio amplifier from scratch in order to demonstrate that such a key device can be constructed using basic electrical engineering principles. After performing major circuit calculations by hand, we... Continue Reading
    ABSTRACT An audio AMP is basically a system which is used as a means of increasing the level of sound or audio signals for maximum use. A public address system consists basically of microphone, Amplifier and speaker(s) to facilitate the communication to intelligible speech to groups of people... Continue Reading
    ABSTRACT This thesis gives the account for the design and construction of a 45W Audio Power Amplifier with the objective of producing a reliable and cheaper amplifier that can be used in a household or stage. The Audio Power Amplifier was constructed with electrical/electronics components such as resistors, capacitors, transformer, transistors and... Continue Reading
    Call Us
    whatsappWhatsApp Us