Most Read Chemical Engineering Project Topics and Materials (Page 20)

ABSTRACT The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel iron for special p2rts. The technological properties passed by the chosen mild steel are;... Continue Reading

ABSTRACT The hydrocyclone is a separating device used for the separation of dust particles from air, which has no moving component parts. This mechanism can also be defined as a system of winds circulating about a center of relatively low barometric pressure and on the earths surface, blowing inward in spiral form. This project is constructed for... Continue Reading

In preparation and characterization of adsorbent obtained from corn curbs, potassium hydroxide was used as an activating agent at ratio of 1:1, 7:8 and 3:4 with the corn curbs and their pH values were found to be 8.5, 8.03 and 8.0 respectively, ash content were found to be 41.56, 46.78 and 48.31wt%. The BET surface area values were 17.762461,... Continue Reading

ABSTRACT It is proposed to design a process plant that will control nitrogen oxide emission from a plant that is producing 90wt% nitric acid of 30,000 tonnes of nitric acid. This capacity is based on 8000hours of operation per year i.e. 330 days. It is proposed that this plant will be located in any location where there is substantial release of... Continue Reading

ABSTRACT This study has its theme as a utilization studies of Enugu coals with the view of studying its properties, classification, preparation storage etc comparing coals obtained from different locations. The Enugu coal is a sub-bitummous and non coking coal.  It is very rich in waxes and resins, thus it may be suitable for the production of... Continue Reading

ABSTRACT Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs.  Generally, interface is a boundary layer, so the boundary between two products when they are pumped in succession is known as interface. In Nigeria Petroleum Industries like NNPC (PPMC) make use... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the local... Continue Reading

ABSTRACT Blender is an electric machine for size reducing soft food or liquid mixture.  Blender is some time called liquidizer consists of a glass jar or jug containing a steel blade assembly at the base driven by a small electric motor. Construction of blender was done based on the principle of size of reduction using electric motor as the major... Continue Reading

The spread of pollutant in an area is partly a function of wood burning in local kitchens by the population of the area. This pollution generated through combustion of wood  fuels presents difficult environmental challenges to societies as it could degrade the environment and affect human health and quality of life. Wood burning emissions are... Continue Reading

ABSTRACT The potential advantage and application of the photocatalytic process using titanium dioxide as the photocatalyst to treat industrial waste water in UV irradiation has been reported. The aim of this work is to investigate the effectiveness of photocatalytic degradation using TiO2 in treating pharmaceutical waste water. Wastewater was... Continue Reading

ABSTRACT This project was carried out using coal sample from Onyeama coal mine Enugu, Enugu State. Activated coal was produced by carbonizing the coal and activating it using phosphoric acid at a temperature of 5500c.  the degree of bleaching of raw palm oil was monitored using spectronic meter through absorbance measurement.  The essence was... Continue Reading

ABSTRACT Water is one of the most important substances on earth. All plant and animals must have water to survive. If there is no water there would be no life on earth. Disease causing germs and chemicals find their way into water supplies when this happens, the water becomes polluted. The principal objective of this research work is to asses the... Continue Reading

This project contains details of Coal fired circulating fluidize boiler.The motivation of our project was to develop a method which is energy economical i.e. uses less energy owing to increasing energy issues. Process description, mass balance, energy balance, equipment design, and cost estimation of circulating fluidized bed boiler for combustion... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the  possibility of producing plane mirror using sand rich in silica as its major local raw material.Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the local... Continue Reading

ABSTRACT The project dealt on the production of yam flour from yam chips. The yams were peeled and washed, 100grams samples coded sample A to G were subjected to two different drying conditions. Some were dried using the sun drying method while the others were dried through oven drying method kept at constant temperature of 500C, sodium... Continue Reading

ABSTRACT             The advent of sachet and bottled water has increasingly filled the gap in household water security. This research work was carried out to assess the quality of bottled and sachet water sold in Bauchi metropolis. Thirty (30) water brands consisting of twenty (20) sachet water brands and ten (10) bottled water brands... Continue Reading

ABSTRACT In the construct of 2,000 litres capacity water reservoir galvanized  steel  sheet forms the tank and an angle iron rod forms the stand.  Two full length galvanized sheet were marked out and cut out to the required sizes.  The work stated by cutting the it gauges galvanized steel sheets of full length into geometrical dimensions of... Continue Reading

                                                                      EXECUTIVE SUMMARY       This work presents the design of a plant that will produce 250000kg/yr of lindane from benzene, chlorine and water at high temperature and pressure using direct chlorination method.... Continue Reading

 ABSTRACT Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs.  Generally, interface is a boundary layer, so the boundary between two products when they are pumped in succession is known as interface.In Nigeria Petroleum Industries like NNPC (PPMC) make use... Continue Reading

The project research entailed the production of high quality sealant  incorporating a local raw material for sealing holes and gaps in various materials  like metal and plastic. Two samples of acrylic sealants were produced, the first  samples which is the standard formulations involved the use of silica gel as a  major adhesion promoter and... Continue Reading

ABSTRACT This report aimed at determining  the presence and removal of mercaptan sulphur in kerosene using colour indicator method.  It is known that impurities such as free  sulphur,  sulphur dioxide, mercapters, funing materials etc. are found in petroleum products. Consequently,absorbents like molecular sieve, calcium oxide and even... Continue Reading

ABSTRACT The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing... Continue Reading

ABSTRACT A comparative investigation was undertaken to determine the head loss coefficients for horizontally mounted and vertically mounted orifices using a Fluid mechanics and Heat transfer trainer developed in Nigeria. Experiments were carried out observing the procedure and the discharge of the flow of water was collected to obtain the... Continue Reading

ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method.  It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated... Continue Reading

ABSTRACT The repair of the fixed bed adsorption column, a product of arm field technical company was carried out for the purpose of bringing the faulty equipment back to its normal operating system. Before this exercise, the equipment was out of operation because of the completely blocked base of the fixed bed column (water column) and the... Continue Reading