+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

REPAIR AND REFURBISHING OF PILOT PLANT TEMPERATURE CONTROL APPARATUS

  • Type:Project
  • Pages:20
  • Format:Microsoft Word
(Chemical Engineering Project Topics & Materials)
ABSTRACT
The objective of the repair and refurbishing the pilot plant temperature control equipment is to keep the apparatus in good working condition for it to be used for its various purposes.

The part of the temperature control changed and new one installed. This was due to series of faults developed by the former one” Electrical accessories were also changed for efficient power supply to the equipment.

General maintenance operations were carried out on the equipment pipes, air hoses, clips, nuts, and thermometers.  The sum tank was cleaned to remove dirt’s that stick on the surfaces.  Metal body filler was used in that stick on the surfaces.  Metal body filler was used in filling / covering the leakages. 

Finally, the temperature control equipment was in good working condition and henceforth, can used for future engineering practices.    

INTRODUCTION
Temperature control equipment is the apparatus used by chemical engineers to balance the requirements of maximum efficiency and complete control over a process.  It is designed to show the working of a heat exchanger and it permits series of experiments to be performed with it.  Water is both the process fluid and the heating fluid, the rate of flow of the later being controlled either manually or automatically using the process fluid inlet temperature to provide the control signal.

In some decades ago, when industries were trying to overlook their ways into the production of goods on large scale without much waste from the available raw materials.  Certain variable like temperature applied to fluid or rather dictated from body, fluid flow rate, pressure, etc.  This give rise to loss of valuable materials, money and other things like waste of time.  Thus in pilot plant, where there is production of goods in small scale.  This problems listed above was encountered which give rise to the introduction of temperature control apparatus to regulate, these problems.

The equipment is made up of a closed circuit known to be primary hot water system supplying heat to a secondary water system fed from the mains.  A plate type heat exchanger transfers heat from the primary to the secondary system.  Chemical reactions are usually exothermic, and it may well be important to remove heat via a heat exchanger rather than supply it so as to avoid temperature rise.  Heat exchange is one of the most frequent operations in process industries.  It large numbers of process proceed at a much faster rate as the temperature is raised.  It is economically advantageous to use high temperature as possible because of its positive contribution in chemical reaction.

The thermometer allows the inlet and outlet temperature of the heating fluid and the process fluid to be determined.

REPAIR AND REFURBISHING OF PILOT PLANT TEMPERATURE CONTROL APPARATUS

Share This

Details

Type Project
Department Chemical Engineering
Project ID CNG0329
Price ₦3,000 ($9)
No of Pages 20 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0329
    Price ₦3,000 ($9)
    No of Pages 20 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT A temperature control apparatus an “Armfield model was refurbished. The methodology employed were to detect the pulty parts of the equipment especially in the sump where leakages were observed. In the repair, the water in the sump was drained off, corrosion and rusting in the tank were... Continue Reading
    ABSTRACT           The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.           The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is... Continue Reading
    ABSTRACT Spray substance are used to make home grnow powered substance whose particles are usually spherical in shape and approximately 10-40 micro s. The maintenance of pilot plant spray dryer was stated with observation of the faults in the spray dryer. The faulty components were dismantled, serviced and... Continue Reading
    ABSTRACT     The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.     The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is driven by an electrically... Continue Reading
    ABSTRACT           The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.           The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is... Continue Reading
    ABSTRACT             The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.             The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer,... Continue Reading
    ABSTRACT The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint. The project cut across all forms of engineering, such as mechanical machine... Continue Reading
    ABSTRACT The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint. The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is driven by an electrically made device, a... Continue Reading
    ABSTRACT Brazing alloys used for brazing the components of gas turbines and aerospace applications contain nickel as the base material. Nickel has highest affinity for oxygen. Incase if components are brazed using nickel as based filter material in air or atmosphere the braze joint will porous and braze strength is not achievable. To avoid the... Continue Reading
    ABSTRACT Brazing alloys used for brazing the components of gas turbines and aerospace applications contain nickel as the base material. Nickel has highest affinity for oxygen. Incase if components are brazed using nickel as based filter material in air or atmosphere the braze joint will porous and braze strength is not achievable. To avoid the... Continue Reading