+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

CONSTRUCTION OF WATER STORAGE TANK (2000 LITRES)

  • Type:Project
  • Pages:23
  • Format:Microsoft Word
(Chemical Engineering Project Topics & Materials)
ABSTRACT
The 20000 liters storage tank was constructed for effective storage and conservation of third with three (3) mild steel sheet of 14 gauge (2mm) thickness. 
The construction started by marketing out 1½ (One and half) mild steel of 2440 Mm by 113Mmusing metal meter rule and critter the already market out dimension underwent cutting with a backsaw and after marking out and cutting operation of the cylindrical part it under went fording, using hammer and folding machine, and finally joined together using Arc welding machine. 

Therefore, the cylindrical part of the storage tank was formed. To form the bottom , half of the remaining sheet, that was used initially for the cylindrical part was used, having a dimension of 1220 MM by 1130MM The top of the tank has a doomed sphere, roof of 1220MM for the entering of water and it was coured with the constructed culver of 40000 MM by 10000 MM using one mild steel sheet the storage tank socket and tap was designed and constructed using drilling machine to make a small opening at the bottom of the tank with a diameter of 2.5MM and the inner threaded socket pipe of diameter 30Mmby 60 MM was screwed and welded to the opening. The complete are welding of the parts was done with 12 gauge 2.5 MM electrode with exit piping of all the necessary joints. The storage tank was designed for affective storage and transfer of water through the tap control. It was discovered that the flow rate of the water through the tap control was free of any obstruction therefore, the tap can allow easy water flow out from the tank and can be used ford for storage of any water such as kerosene diesel, petrol etc. The construction was achieved this water was filled into function effectively. 
 
 TABLE OF CONTENT
COVER PAGE
TITLE PAGE
LETTER OF TRANSMITTAL
DEDICATION
ACKNOWLEDGEMENT
APPROVAL PAGE
ABSTRACT

CHAPTER ONE
1.0 INTRODUCTION
1.1 SCOPE OF THE PROJECT

CHAPTER TWO
2.0 Types of reservoirs
2.1 Industrial and domestic use of reservoir
2.2 Materials of construction for different types of reservoirs
2.3 Design factors for construction

CHAPTER THREE
3.0 Procedure for construction of 500 gallons 2250 litres
3.1 Installation procedure for the tank
3.2 Cost estimate/evaluation

CHAPTER FOUR
4.0 RECOMMENDATIONS
Conclusion
References
 

CONSTRUCTION OF WATER STORAGE TANK (2000 LITRES)

Share This

Details

Type Project
Department Chemical Engineering
Project ID CNG0327
Price ₦3,000 ($9)
No of Pages 23 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0327
    Price ₦3,000 ($9)
    No of Pages 23 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The 20000 liters storage tank was constructed for effective storage and conservation of third with three (3) mild steel sheet of 14 gauge (2mm) thickness. The construction started by marketing out 1½ (One and half) mild steel of 2440 Mm by 113Mmusing metal meter rule and critter the already market out dimension underwent cutting with a... Continue Reading
    ABSTRACT The 20000 liters storage tank was constructed for effective storage and conservation of third with three (3) mild steel sheet of 14 gauge (2mm) thickness. The construction started by marketing out 1½ (One and half) mild steel of 2440 Mm by 113Mmusing metal meter rule and critter the already market out dimension underwent cutting with a... Continue Reading
    ABSTRACT In the construct of 2,000 litres capacity water reservoir galvanized steel sheet forms the tank and an angle iron rod forms the stand. Two full length galvanized sheet were marked out and cut out to the required sizes. The work stated by cutting the it gauges galvanized steel sheets... Continue Reading
    ABSTRACT In the construct of 2,000 litres capacity water reservoir galvanized steel sheet forms the tank and an angle iron rod forms the stand. Two full length galvanized sheet were marked out and cut out to the required sizes. The work stated by cutting the it gauges galvanized steel sheets of full length into geometrical dimensions of the... Continue Reading
    ABSTRACT The evaluation of microbiological quality of tank water at the Institute of Management and Technology campus III Enugu was carried out by using ten samples of water obtained from ten different tank waters. For viable plate count for the presence of pathogenic organisms and organisms indicating organic matter pollution, plating technique... Continue Reading
    ABSTRACT This research is focused at designing of water storage facilities of size 875,000 litres (750,000 litres for underground water storage, and 125,000 Litres for elevated steel tank) of treated wastewater and its transmission system for the storage and re-use of treated wastewater. The project is aimed to structurally design water storage... Continue Reading
    CHAPTER ONE 1.0 INTRODUCTION 1.1 Statement of the Problems 1.2 Objectives of the Study 1.3 Scope & Limitations of the study 1.4 Specifications the following abbreviations are used CHAPTER TWO LITERATURE REVIEW CHAPTER THREE MATERIALS AND METHOD CHAPTER FOUR DESIGN AND IMPLEMENTATION CHAPTER FIVE SUMMARY, CONCLUSION AND RECOMMENDATION... Continue Reading
    ABSTRACT This study was aimed at developing a rational approach to septic tank design in order to reduce health risks associated with improperly treated effluent especially in developing countries. To this end, several research tools including questionnaires, pilot scale study and model formulation were employed. Questionnaires were used to... Continue Reading
    ABSTRACT The construction of the 500 gallous (2,250 litre) of water is a project which has definite mathematical patterns. The choice of a cylindrical pattern of design involved the application of mathematical deductions to analyse the size of materials required. The introductory and scope... Continue Reading
    ABSTRACT This project, aimed at investigating the anaerobic processes in septic tank as a waste water treatment option using waste water from septic tank and Soakaway as sample A and B respectively. It was observed that after the  analysis, sample A (septic tank which has fresh waste water) has higher value in conductivity =1708us/ cm3, Total... Continue Reading