CONSTRUCTION OF GRAIN GRINDING MACHINE

(Mechanical Engineering)

CONSTRUCTION OF GRAIN GRINDING MACHINE

ABSTRACT

            The aim of the project is to construct a domestic grain grinding machine to be powered by electric motor through pulley and belt transmission.

            The project is to perform mostly blending and grinding on grains e.g beans, maize, melon, millet and such other food crops.

            In construction of the project, there are various factors that is being put into consideration.

i.                    The size specification

ii.                  The power of the electric motor to be used

iii.                The domestic operation which can be performed by the machine.

iv.                The capacity of the machine.

TABLE OF CONTENTS

CHAPTER ONE

Introduction                                                               

1.1       Research problem                                                       

1.2       Justification of the study                                           

1.3       Objectives of the study                                              

1.4       Scope and limitation  

CHAPTER TWO

Literature review                                                        

Existing grinding machine                                         

CHAPTER THREE

Description of the machine                            

CHAPTER FOUR   

Analysis and size specification                                              

Calculation analysis                                                               

CHAPTER FIVE

Maintenance                                                               

Operation procedure                                                  

CHAPTER SIX

Conclusion                                                                             

Recommendation for further work                

Reference                                                                               

                                                                                   

 

LETTER OF TRANSMITTAL

Sir,

SUBMISSION OF REPORT ON PROJECT (MEC 220)

 

Having completed the work on the project about which this report written under the supervision of ……….We the undersigned take pleasure in the submission here with the said report for the considerations of the departmental board in accordance with the award rules and regulation of the National Board for Technical Education (BNTE).

Yours faithfully,

CHAPTER ONE

INTRODUCTION   

            Every year, the final year student of this institution in Higher National Diploma (HND) and the National Diploma (ND) into practice.

            This is aimed at justifying the emphasis lead on practical work during the course of study in the assigned to construct a grain-grinding machine by the machine committee of Mechanical Engineering Department, the Polytechnic, Enugu.

            A grain grinding machine is an equipment used for grinding maize, beans, melon, millet and such other good crops.  This equipment comprises essentially of an electric motor, belt, pulley, transmission shaft, hopper, mills, spiral conveyor and stands. These alleviate the rigours and problems house we encounter when grinding beans for the good stuff.

1.1       RESEARCH PROBLEMS

            The project research problem are:

i.                    To construct a local fabricated grain grinding machine using available local technology.     

ii.                  To construct a machine with a size specification.

iii.                To construct a machine which can perform a domestic operations.

iv.                To construct a machine which have adequate capacity, lighter in weight, lesser fatigue and portable.

1.2       JUSTIFICATION OF STUDY

i.                    This is to promote indigenous machine and their producers.

ii.                  To have a portable grain grinding machine constructed for domestic uses with a powered driven source.

iii.                To improve the economic and the country as a whole by neglecting imported blenders i.e producing machine that is affordable to substitute the imported blenders.

iv.                To be able to meet National Board for Technical Education (NBTE) requirement in awarding National Diploma (ND) in Mechanical Engineering.

1.3       OBJECTIVES OF THE STUDY

            The objectives of the study are:-

i.                    To construct grain grinding machine with local materials.

ii.                  To construct a machine which is less in crop and domestic usage.

iii.                To produce a grain grinding machine that is lesser in vibration, weight and in size.

 

 
 
 

 

 

Folding the four

side at right angle

 

Hopper

 

               Shaft

 

 

 

            Semi circular pipe f 82

 

 

 

 

                          45

 

 

Frame support

TERMS AND CONDITIONS

Using our service is LEGAL and IS NOT prohibited by any university/college policies

You are allowed to use the original model papers you will receive in the following ways:

1. As a source for additional understanding of the subject

2. As a source for ideas for your own research (if properly referenced)

3. For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase)

4. Direct citing (if referenced properly)

Thank you so much for your respect to the authors copyright.

For more project materials

Log on to www.grossarchive.com

Or call

+2348130686500

+2348093423853

 

500
Leave a comment...