THE CONSTRUCTION AND FABRICATION OF A CANDLE MOULDING MACHINE

(Mechanical Engineering)

THE CONSTRUCTION AND FABRICATION OF A CANDLE MOULDING MACHINE

ABSTRACT

The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light.

In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important.

The major components of the candle molding machine are: the castled aluminum body, the adjustable screw, which serves as a separation between the too moulds cop and drag (male and female).

The reason why there is no cooling system is because the body is made of non – ferrous metal (aluminum) which does not create much vacuum for heat addition as much as steel do and also the mould has operate in opening system which admit natural air inside the mould when opened to cool the max and enhance the quick solidification of the wax. The mould due to its opening system, it works more efficiently under cool whether condition.

TABLE OF CONTENTS

CHAPTER ONE

1.0       Introduction

1.1       Background Information of Candle Moulding Machine

1.2       Problems of the Project (Candle Moulding)

1.2.1    Lack of Research Materials

1.2.2    Cost Involvement

1.2.3    Time Factor

1.2.4    Market Demand

1.2.5    Thread Centering Mechanism

1.2.6    Melting / Pouring

1.3       Aims and Objectives of the Investigation on Candle Moulding Machine

1.3.1    Production of Cost of Production

1.3.2    Improvement on the Pouring Mechanism

1.3.3    Improving Market Demand

1.3.4    Improving of the Thread Centering Mechanism

CHAPTER TWO

Literature Review

CHAPTER THREE

Design Concepts and Analysis

CHAPTER FOUR

Mode of Construction

CHAPTER FIVE

Cost

CHAPTER SIX

Conclusion and Recommendation

References

CHAPTER ONE

 

1.0       INTRODUCTION

In every developing nation like ours, it is supremely pertinent to acquaint ourselves with fabrication of machines and components. The clamour for indigenous technology should not be a lip service but should be pragmatic, so that our abundant local raw materials can be affectively utilized.

One area effort has been made is in the fabrication of candle moulding machine. Candle is one of the domestic items which all and sundry is cognizance of the indispensable role it plays in our various homes. We should not depend on the importation of such vital domestic item –candle.

However, there are already exiting machines for moulding of max into candle. Most of them are complicated in their design and their operations require the knowledge of skilled men and personnel to supervise the operation. Not only this, the cost of importing them here is not a taken, consequently, a candle moulding machine which does the same function of converting max into candle stick has been developed.

The candle mould is not costly, not complicated in design and does not require the knowledge of skilled men for its operation. It is manually operated and can be used in our college industries but owning to the limited number of mould cavities it is more advantageous in our home to produce candlestick when the need arises.

This project, aims at giving solutions to the problems encountered in the previous related project at most economic level. In our material selection we put into consideration of various materials that can be used to produce the fabrication and with which the machine can function satisfactorily at maximum level of safety.

1.1       BACKGROUND INFORMATION OF CANDLE MOULDING MACHINE

The candle moulding machine shares the same principle as the giant ones produced before it. Likes the gaint ones, it works on the principle of casting. Candle making can be described as the casting of wax into stick form. The molten wax is poured into the mould cavity and is allowed to solidify.

The machine has a moulding box (made of aluminum) having 15 cavities with each cavity making 15mm diameter and mm length approximately.

There is adjustable screw, which move the mould in horizontal axis and also open and closes as each cast. Due to its opening system the solidification is enhanced quickly.

Melting of the wax is external to the machine and pouring is done as soon as the wax becomes molten.

1.2       PROBLEMS OF THE PROJECT (CANDLE MOULDING MACHINE)

In the course of the research for the fabrication of candle mould that commensurate with contemporary level of technology, many several factors militated against our urge that we are constrained to producing a manually operated candle moulding machine. The problem we had encountered includes the following: -

1.2.1 LACK OF RESEARCH MATERIAL

Not available for deeper research in this project. There is no text –book that gives a cogent means of advancement in the fabrication of the candle moulding machine. We were ambitious in modernizing the existing candle moulding machine built in the school and others seen else where, but the information gathered from them could only help us to develop a similar candle mould, though with little addition in the number of mould cavity and erodent discharge mechanism.

1.2.2 COST INVOLVEMENT

Cost has been limiting factor in a very research work. In this project the available fund is not enough to help us visit as many libraries and research centers as possible. We could only visit the ones within our vicinity in ensuring that the cost of production does not over weigh us.

1.2.3 TIME FACTOR

This project is scheduled with a given frame in path and through research is not possible within the time given. We strived to conduct the research and the production within the given frame of time.

1.2.4 MARKET DEMAND

A factor we put into consideration in the course of this study is the market demand. We anticipate the patronage that can be given to this machine even when it is designed elaborately with high cost of production. Technology development has come up with many inventions, which are close substitute for candle. The invention of rechargeable leathern and like is gradually phasing off the  use of candle. If huge money is committed in developing automatic candle moulding machine, the cost of purchasing the machine becomes high and consequently its substitute would be considered.

1.2.5 THREAD CENTERING MECHANISM

It has been observed that the existing candle – moulding machine has a poor mechanism for centering the wick in the candle wave. This is a major problem encounter in the designing of a simple way of centering the wick (thread).

1.3       AIMS AND OBJECTIVES OF THE INVESTIGATION ON CANDLE MOULDING MACHINE

As with any other project investigation, there are various aims and objectives that necessitated this aims are dependent of the problems of the candle – moulding machine. Mostly, the aims are intended for given solution to the problems encountered in related projects, particularly, the previous project done by our predecessor in this school and in other school of which ESUT is among.

The following are among the aims and objectives of the investigations on candle moulding machine.

1.3.1 REDUCTION OF COST OF PRODUCTION

While we are engaged in the production of the candle – moulding machine at the minimum economic level, we have selected a material uneconomic level, we have selected a material that is cheap when compared with other related materials. This material aluminum though not so cheap, is as good as, the other costly ones, we also put cost into consideration when selecting the eject mechanism.

1.3.2 IMPROVEMENT ON THE POURING MECHANISM

In the previous project, the mould cavity was filled one at a time. This creates the problem of non-uniform solidificacation and time wastage. This project has been gone a long way of improving pouring mechanism. Though the melting of the waste is external to the machine and then introduced to the cavities as in the previous project, design of the top of the cavity are such that pouring is done one after another at once.

1.3.3 IMPROVING MARKET DEMAND

As have been said the cost of production is reduced to the barest minimum. This is a strategy to increase the demand for this machine since it has seriously competing substitutes. As the production cost reduced, prospective customers then can afford the machine.

1.3.4 IMPROVEMENT OF THE THREAD CENTERING MECHANISM

In this project, the problem of misalign thread along the centre of candlestick is dealt with the mechanism is though simple but effective. This one, the thread was alignment out both up and Bolton of the mould, centered with nails welded permanently on a 2mm thick flat bar.

  TERMS AND CONDITIONS

Using our service is LEGAL and IS NOT prohibited by any university/college policies

You are allowed to use the original model papers you will receive in the following ways:

1. As a source for additional understanding of the subject

2. As a source for ideas for your own research (if properly referenced)

3. For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase)

4. Direct citing (if referenced properly)

Thank you so much for your respect to the authors copyright.

For more project materials

Log on to www.grossarchive.com

Or call

+2348130686500

+2348093423853

 

500
Leave a comment...