+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

PRODUCTION OF PLANT MIRROR USING LOCAL RAW MATERIAL

  • Type:Project
  • Pages:65
  • Format:Microsoft Word
(Chemical Engineering Project Topics & Materials)
ABSTRACT

This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material.
Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the local raw material used in the in the production of plane mirror in this product backing paint.  The facilities for the production include spraying gun and finger brush.
In the course of production, the silver nitrate was first mixed with a reducing reagent; we formaldehyde of glucose, all in a distilled water.  After which the mirror backing paint was mixed with some amount of thinner.  The float glass was then washed with warm water and allowed to dry.  After drying, it was first coated with silver nitrate solution after the use of talcum power to rub on the back of the glass.

A second spraying of mirror- backing paint was done after the silver nitrate coating had dried up.  This whole operation now resulted to a plane-mirror since a plane mirror is also a coated glass.
The reflection of the mirror was taken after coating the glass, while the refractive index of the glass was taken before coating the float glass to form a mirror.
 
TABLE OF CONTENT

Title page
Approval page
Letter of transmittal
Dedication 
Acknowledgement
Abstract
Table of content

CHAPTER ONE
INTRODUCTION
1.1Historical Background
1.2Definition:
1.3Aims:
1.4Scope of Study:
1.5Uses:
1.6Properties:

CHAPTER TWO
1.0LITERATURE REVIEW
2.1Plane Mirror
2.2Raw Material for Production of Plane Mirror
2.2.1Sand
2.2.2Soda Ash (Sodium Trioxocarbonate Iv)
2.2.3Limestone (Calcium Trioxocarbonate (W)
2.3.0Other Raw Material (Ie Additives)
2.3.1Colouring and Decolourizing Agents
2.3.2Melting and Refining Agents
2.3.3Opalizing Agents
2.2.4Modifiers
2.3.5Cullet
2.40Types of Furnaces
2.4.1Tank Furnance
2.4.2Pot Furances
2.4.3Day Tanks
2.4.3Recuperative Furnance
2.5.0Glass Formation
2.5.1Glass Melting Process
2.5Preparation of the Batch
2.5.1Melting Of Glass
2.6   Types of Glasses
2.6.2Float Glass
2.7Manufacture of Mirror
2.7.1Sequence of Production
2.7.2Cutting
2.7.2Labelling
2.7.3Polishing
2.7.4Washing Operation
2.7.5Silvering Spraying
2.7.6Painting
2.7.7Oven
2.7.8Cleaning and Inspection
2.7.10Drilling
2.8.0Types of Mirrors
2.9.0Optical Properties of Mirror
2.9.1Refractive Index and Dispersion
2.9.2Transparency

CHAPTER THREE
3.0Experiment Procedure for Production Of plane mirror
3.1Raw Materials
3.2Apparatus/Equipment
3.3Preparation of mirror silvering chemical
3.4Operational procedures involved in the production of plane mirror
3.5Experimental Result
3.5.1Refractive Index Of Glass
3.5.2Reflection of Plane Mirror
3.61Experimental Date For Refractive Index
3.61.1Experimental Data For Reflection
3.5.2Reflection of Plane Mirror


CHAPTER FOUR
DISCUSSION

CHAPTER FIVE
CONCLUSION

CHAPTER SIX
RECOMMENDATION

PRODUCTION OF PLANT MIRROR USING LOCAL RAW MATERIAL

Share This

Details

Type Project
Department Chemical Engineering
Project ID CNG0222
Price ₦3,000 ($9)
No of Pages 65 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0222
    Price ₦3,000 ($9)
    No of Pages 65 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The project aims to develop a flow process to obtain the optimum temperature and time necessary for the maximum recovery of alkali present in palm inflorescence. On this ground, a preliminary experiment was performed. During this process, both male and female palm inflorescence were compared for maximum alkali production and it was... Continue Reading
    ABSTRACT The project aims to develop a flow process to obtain the optimum temperature and time necessary for the maximum recovery of alkali present in palm inflorescence. On this ground, a preliminary experiment was performed. During this process, both male and female palm inflorescence were compared for maximum alkali production and it was... Continue Reading
    INVESTIGATION OF THE PRODUCTION OF GOOD QUALITY ETHANOL FROM LOCAL RAW MATERIAL (CASSAVA) USING MICRO ORGANISM WITHIN OUR LOCALITY ABSTRACT A literature review of ethanol production from local materials especially from cassava is presented. The study was carried out to investigate the production of a good quality ethanol from cassava using... Continue Reading
    Negotiation as A Cost Reduction Technique In Material Procurement at Nigerian Bottling Company Plc Kaduna Plant CHAPTER I:    Introduction Every human being needs water to survive, so also every organization needs materials to survive. In the private and public sector, their total expenditure is mainly spent on acquiring either materials or... Continue Reading
    ABSTRACT           The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.           The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is... Continue Reading
    ABSTRACT     The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.     The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is driven by an electrically... Continue Reading
    ABSTRACT This project is on the production of paint from the available materials.  The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc.  the next step is the proper production procedure.  The  same product patterns was employed while the production was valued with a view to... Continue Reading
    ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was... Continue Reading
    ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was employed while the production was valued with a view to obtain... Continue Reading
    ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was... Continue Reading