Most Relevant Chemical Engineering Project Topics and Materials (Page 13)

ABSTRACT This project is on the production of paint from the available materials. The first process involved was the sourcing of the available material which include calcium carbonate (dotonute) water etc. the next step is the proper production procedure. The same product patterns was employed while the production was valued with a view to obtain... Continue Reading

It's a journal that explains the design of a shea butter plant.... Continue Reading

ABSTRACTA study on the effects of post- harvest variables on the yield and quality of Shea butter wascarried out. The Shea nuts acquired from villages were divided into five batches with avillage/uncontrolled sample. Each batch was boiled at different time ranges (0, 15, 30, 45 and60) minutes. Each batch was dried through an oven drying method.... Continue Reading

Crude oil viscosity is an important parameter which is considered in both porous media and in pipeline channels. Estimating oil viscosity at various operating conditions of pressure and temperature is of great value to petroleum engineers. In petroleum and reservoir engineering, we are often faced with the analysis of processes which involve... Continue Reading

Kenaf reinforced polyethylene composites for ballistic protection was produced in this work. The samples of alkaline treated and silane-coupled non-woven matted kenaf fibers were cut to the required dimensions and oriented vertically and horizontally in combinations with a virgin high density polyethylene (VHDPE). The composite panels were... Continue Reading

This project contains details of Coal fired circulating fluidize boiler.The motivation of our project was to develop a method which is energy economical i.e. uses less energy owing to increasing energy issues. Process description, mass balance, energy balance, equipment design, and cost estimation of circulating fluidized bed boiler for combustion... Continue Reading

ABSRACT The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component... Continue Reading

ABSTRACT This is an abstract on the construction of a packed distillation column. A packed distillation column is used in the separating process distillation that is the separation of two miscible liquids. It was constructed by marking out the dimension of the column, condenser, pot, using steel rule scriber, oxyacetylene flame was used for... Continue Reading

ABSTRACT The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing... Continue Reading

ABSTRACT This project was carried out using acid activated coal from Enugu coal and the production of ve4getablew oil was monitored using spectrophotometer to measure the absorbance. It was also perform to check the suitability of activated Enugu coal as a bleaching agent for palm oil. The Enugu coal samples were collected, size reduced,... Continue Reading

ABSTRACT The fresh cassava were sources from Idodo in Nkanu Local Government of Enugu state. The weight of the cassava tuber were taken to be 31.50kg. After peeling and washing, it was divided into two equal parts which was 21.13kg for production of sample A and sample B respectively (edible and textile starch) which weighed 13.1kg. During this... Continue Reading

ABSTRACT Bioremediation is an important technology for the restoration of oil polluted environments by indigenous or selected microorganisms. In general, the rate of biodegradation depends on the number and types of micro-organism, the nature and chemical structure of pollutants to be degraded and the environmental conditions. In this study, the... Continue Reading

The spread of pollutant in an area is partly a function of wood burning in local kitchens by the population of the area. This pollution generated through combustion of wood  fuels presents difficult environmental challenges to societies as it could degrade the environment and affect human health and quality of life. Wood burning emissions are... Continue Reading

ABSTRACT This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot. In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time. The three major... Continue Reading

INTRODUCTION The separation operation of drying converts a solid, semi-solid or liquid feedstock into a solid product by evaporation of the liquid into a vapor phase via application of heat. In the special case of freeze drying, which takes place below the triple point of the liquid being removed, drying occurs by sublimation of the solid phase... Continue Reading

ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method. It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass. Presently in Nigeria, sheet glass is not used easily produce and as such, the local raw... Continue Reading

ABSTRACT After detailed study on machines and levers, the construction work started as follows:- Making out, pattern development, cutting filling, drilling, machining, assembling, welding and finishing. Detailed procedures carried out is located at the sequence of operation in subsequent pages. The machine has scale of 1:5 in all parts of its... Continue Reading

ABSTRACT The purpose of the project is to study the effect of liquid flow rate and gas flow rate on the pressure drop in a packed absorption tower and also to repair and restore the packed absorption tower to good working condition. Trouble shooting revealed that the exit drain value was broken due to carelessness on the part of former user of the... Continue Reading

ABSTRACT This project “Characteristics Of Local Produced Oil From Groundnut Oil” was carried out using ten cups of groundnut seeds that was purchased from a local market in Enugu metropolis. The oil these seeds were in Enugu using solvent extraction method. Two different solvents were used in the extraction namely: Ethane and order to compare... Continue Reading

ABSTRACT This study has its theme as a utilization studies of Enugu coals with the view of studying its properties, classification, preparation storage etc comparing coals obtained from different locations. The Enugu coal is a sub-bitummous and non coking coal. It is very rich in waxes and resins, thus it may be suitable for the production of... Continue Reading

ABSTRACT The design and construction of s refrigerating unit is handled from the knowledge of the working principles of laws of thermodynamics. The size of the containing vessel i.e the case as established to be of 45cm by 32 cm in dimension. The Angle iron mild steel to used in the fabrication and welding. The box case of two layers are... Continue Reading

ABSTRACT A table top liquid-liquid extraction unit was constructed. The project also involved the repair and servicing of peristaltic suction pump, by painting it, replacing the connecting cord to the power supply, refilling of the work out suction plates, teeth and general servicing of the equipment. The glass absorption columns were provided as... Continue Reading

ABSTRACT In account form analysis, a lot of discrepancies causes by manual aspect of the form such as: lost of form, inability to correct intakes, poor storage facilities have been a problem in the May fresh savings and loan limited account form. But in recent times, the computer has come to the aid of our banks, May fresh in particular. The... Continue Reading

It is of no doubt that one day, fossil fuels, which the whole world highly depends on, will come to a halt in a few decades to come. To this reason, researches have been geared towards alternative sources of energy: biodiesel, a form of renewable energy (energy that can be regenerated once used up), is one that has been made known and being tested... Continue Reading