The energy sector plays a major role in driving Kenya’s economy. The need to conceive, develop and sustain energy generating sources cannot be underestimated. Being a growing economy, Kenya therefore needs to redirect her effort in production of self-sustaining energy generating sources. It is in this line that the government through the... Continue Reading
TABLE OF CONTENTS Page ABSTRACT ……………………………………………………………………………..iii ACKNOWLEDGEMENTS……..………………………………………………………..iv LIST OF ILLUSTRATIONS………………………………………………………….…vii SECTION 1.... Continue Reading
ABSTRACT This write up is a detail of the process and information of plan for the physical realization of the construction of the 1M3 mobile deep freezer. It is divided into chapters, which discussed extensively the practical refrigeration cycle with full attention given to design factors working principle and choice of material. The method used... Continue Reading
The need for identification leads to the study of biometrics. Over the ages, human beings have been identified by various means, such as the Name, Complexion, Nationality, and even some uniquely assigned codes. Of all these methods, none can be used to uniquely identify an individual distinctly under all circumstances. However, research has shown... Continue Reading
ABSTRACT The Orsat Gas Analyzer was constructed at the project development institute (PRODA), Enugu. The operation involved the laboratory glass blowing which entails the heating of a glass tube. The heating •continues until the glass tube reaches its plastic state. The shape of the tube is changed or the required shape blown by pulling, bending... Continue Reading
ABSTRACT The motive of this project is to construct equipment for deodorizing kerosene, hence the smell of kerosene is totally eradicated. The equipment was constructed with flat sheet plates of a desired standard, the dimension and the truncated parts were coupled and welded in order to fasten the parts together. The material was selected to... Continue Reading
ABSTRACT This project involves the development of a console that allows multiple inputs (3 inputs) and a single output to a screen through the use of software. The micro controller which serves as the ‘heart’ of the hardware was encoded using C programming language. These lines of code enable the micro controller to switch to the selected... Continue Reading
This work is based on automatic changeover switch. If there is failure in main power supply it will automatically change to auxiliary power supply such as generator. This project is based on electromechanical changeover with the use of magnetic contractors, relay,and circuit breaker.... Continue Reading
INTRODUCTION This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault... Continue Reading
ABSTRACT This system “” comprises of many modules which are: The Sensor/Input Unit, Microcontroller Unit and the Output Interface. The sensor detects when the hand approaches the nozzle. Once the approaching hand is detected, the hand dryer produces a very hot to dry the hand as well as... Continue Reading
ABSTRACT Microcontroller has actually revolutionized the world economy as virtually every facet of life is benefiting in one way or the other on the great impact of Microcontroller today.Meanwhile,the technology of Microcontroller has gone long way of which monitoring and interfacing of real world devices to Microcontroller systems can not be left... Continue Reading
Test and measuringinstruments are an indispensable in any electronics research, development ordesign environment. Test and measuring instruments can be categorized asdigital and analog. Analog systems change their signal output linearly with the input and can be represented on a scale by means of a pointer. In the other hand, digital instruments... Continue Reading
ABSTRACT In our present society, wireless communication has become most prevalent and mobile units (hand held devices /GSM/ Computers) are one of the most common equipments for conveying messages wirelessly. Owing to the fact that most youths in our society today on the average make use of at least one wireless device that communicate with other... Continue Reading
The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides... Continue Reading
ABSTRACT In the world today, the use of power supply in electronics equipment and gadgets has increased and it is still increasing. These power supplies are not stable as required by these electronics. This arise the need for the power stabilization as to overcome this problem This project handles this problem very well. Some recommendations were... Continue Reading
ABSTRACT Electricity is fundamental and inevitable to our daily living as it lighting our environment, powers our homes, schools, hospitals, offices, businesses, and aid industrialization, It is a known phenomena that the economic growth of a nation rides on the wheel of electricity. While the telecommunication market in Nigeria has recorded... Continue Reading
Abstract The aim of this work is to characterize properties and microstructure of stainless steel used as a coating on welding of carbon steel sheets. Two carbon steel plates were set as the metal base and the stainless steel coating was applied on the weld bead. The applied process used was the submerged arc welding (SAW) and tests were carried... Continue Reading
Abstract My project is to improve JIT store management system from manual to automated system. Which is used to avoid problem faced by store keeper when store material manually. Store is the place where many varieties of materials are kept for the purpose of work. So at a time of storage is hard to write in document all material listing by... Continue Reading
ABSTRACT This project as the name implies is chosen, designed and constructed with the intention of transmitting information such as musicals news intertainments programs and soon. And all these that are written above are being transmitted to the atmosphere using an electromagnetic, signal, and this particular project design and construction is... Continue Reading
ABSTRACT Security Car Using RFID System. This project is designed to enhance vehicle safety systems available. Thus, this project consists of some combination of equipment and components to create a car security system that meets the security features and use more advanced. RFID (Radio Frequency Identification) is the most reliable way to... Continue Reading
Wireless power transfer (WPT) technologies have been widely used in many areas, e.g., the charging of electric toothbrush, mobile phones, and electric vehicles. This project introduces fundamental principles of three WPT technologies, i.e., inductive coupling-based WPT, magnetic resonant coupling-based WPT, and electromagnetic radiation-based WPT,... Continue Reading
ABSTRACT The document outlines an investigation done in order to study Fifth Generation (5G) systems and to identify a role that satellite systems will play in contribution to the many advanced and diverse demands on existing telecommunication networks. This next generation network is a build-up and phenomenal improvement in wireless communication... Continue Reading
ABSTRACT The conversion of an input AC power at a given frequency and voltage to an output power at different frequency and voltage can be obtained with static circuits called power converters, containing controllable power electronic devices. Various power converters have been developed to fulfill the requirements of the wind power generation.... Continue Reading
The power system is a highly nonlinear system that operates in a constantly changing environment; loads, generator outputs, voltage controllers, transmission lines, topology, and key operating parameters change continually. The behavior and output of the generators can be affected in a transient conditions. This transient condition can change the... Continue Reading