Most Relevant Chemical Engineering Project Topics and Materials (Page 7)

ABSTRACT The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel iron for special p2rts. The technological properties passed by the chosen mild steel are;... Continue Reading

ABSTRACT The aim of this project was to construct one office table and four chairs. In the course of this project the length of plank used was 12” and we used about 4 number (mahogany) of 1” thickness, ¾ plywood of 1 sheet of 1” thickness, as well as ¼” plywood of ½ and glue 1 tin wenner 1 rod, foam ½ sheet.... Continue Reading

ABSTRACT The purpose of this work was to study the effect of chemical surface properties of activated carbons for their use in water purification. To achieve this objective, activated carbon in both granular and powdered forms namely: as received and devolatilized carbons were prepared. Proximate analysis of the carbon materials was performed.... Continue Reading

ABSTRACT Plants are important in our everyday existence. They provide our foods, produce the oxygen we breathe, and serve as raw materials for many industrial products such as clothes, foot wears and so many others. Plants also provide raw materials for our buildings and in the manufacture of biofuels, dyes, perfumes, pesticides, adsorbents and... Continue Reading

ABSTRACT Phytochemicals are chemical compounds produced by plants, generally to help them thrive or thwart competitors, predators, or pathogens. These chemicals are produced by plants through primary or secondary metabolism (Breslin A,2017) . These work was done to determining the presence of phytochemicals such as Tannins, Saponin, Alkaloids,... Continue Reading

ABSTRACT Plastic and Rubber materials have become the corner stone of our lives, so it leads to generation of huge quantity of waste. These waste materials are either mixed with municipal solid waste or dumped in an open area leading to increase in the area covered under waste land. Plastic and rubber waste, if not recycled is either land filled... Continue Reading

                                                                 ABSTRACT          Biomass is organic materials that are made from plants and animals. Biomass stored alot of energy from the sun. Biomass is renewable sources of energy which can grow more such as trees and crops,... Continue Reading

ABSTRACT   This study was carried out principally for the formulation of artist paint using available raw materials. Paint simplified is a material which may be applied to surfaces in relatively thin layers and which changes to a solid and may occur by evaporation of solvents, by chemical reaction or by combination of the two. Artist paint is the... Continue Reading

ABSTRACT In this research project, the various nail were subjected to six environments so as to check the effect of the environments on corrosion of the nails. Two sets of nails were used; normal nail and concrete nail. Six of each type while the other not coated. The research was carried out in the physical chemical laboratory of the institute of... Continue Reading

ABSTRACT A paint mixer is defined as a pattern constructed for the production (mixing) of paint manually. The method of fabrication of the paint mixer involved a preliminary computation of the dimensions of the standard mixer in relation to the dimension of the reacting vessel in which they will be used in marking out, cutting out to sizes,... Continue Reading

ABSTRACT This project work is on the bleaching of palm oil using activated charcoal. The charcoal used for this work was made from pieces of animal bone by carbonization method.  It was then activated into two different samples.  Firstly, the basic sample was activated using anaphoric acid (H2 s04) while the other was activated by just heating... Continue Reading

ABSTRACT The need for effective and efficient means of oil extraction has been a concern in recent time. Hence, this study aimed at the oil extraction from Moringa oleifera seeds using the Microwave-Assisted extraction method. The extraction process was modeled using Response Surface Methodology (RSM). Also, the evaluation of Moringa oleifera oil... Continue Reading

ABSTRACT The physical properties of CNSL extracted by pyrolysis was studied using standard procedures. The physical properties of the CNSL studied and results obtained compared with other extraction methods (hexane extracted and decarboxylated) from literature are moisture content 4.1%, (6.40%, 3.2%), specific gravity 0.943 (0.926, 0.926)... Continue Reading

ABSTRACT This project was carried using activated local form local corporation Enugu, and the rate of bleaching of palm oil using spectrophotometer by measuring the absorbance. It was also performed to check the suitability of local as a bleaching agent for palm oil. The local from local corporation... Continue Reading

THE POTENTIALS FOR A CO-OPERATIVE THRIFT CREDIT SOCIETY IN A HIGHER EDUCATION INSTITUTION (A CASE STUDY OF I.M.T, ENUGU) TABLE OF CONTENTS CHAPTER ONE 1.1 Background of the study/Introduction 1.2 Statement of Problem 1.3 Purpose of the Study 1.4 Scope of the Study 1.5 Significance of the Study 1.6 Definition of Term 1.7 Research Questions. CHAPTER... Continue Reading

ABSTRACT A cupboard in its proper term. Is a well shaped structure, which could either be rectangular, square or oval in shape, used for the storage of valuables at homes, and offices. Reniff defined cupboard as a rectangular shaped structure of cabinet that accommodates, or is used to keep details for future use.... Continue Reading

ABSTRACT A cyclone is an equipment or a device used for the separation of dust particles from air, which has no moving component parts. This mechanism can also be defined as a system of winds circulating about a center of relatively low barometric pressure and on the earths surface, blowing inward in spiral form.... Continue Reading

ABSTRACT The fabrication of the pilot motorized mixer in volved a preliminary computation of the durunsions of the galvanized steel used, marketing out cutting out to sizes folding, welding, assembling and painting. The dimensions of the motorized mixer are as follows: The vessel is of 300min in diameter and 450mm... Continue Reading

ABSTRACT This project is on construction of size reduction equipment – manual grinder. It was constructed locally with the use of local materials and tools in I.M.T mechanical Engineering workshop. The various parts of the equipment were constructed separately using mild steel before finally coupled.... Continue Reading

CHAPTER ONE 1.0 INTRODUCTION The equipment mostly used in the industries and manufacturing establishments requires the production of definite shape, pattern, different design, embossments and others, are usually moulds. The ability of moulds to withstand pressure, distortion and corrosion determines the... Continue Reading

ABSTRACT The sole aim of this research work is comparison and formulation of industrial Bar Soap and detergent. The major expert of this project deals with quality control processes in the production of a high quality bar soap and detergent. In synthetic detergent which was developed... Continue Reading

ABSTRACT The steel-shelf was constructed at the mechanical engineering workshop of the institute. It was done by first of all making out the dimension with the scribers, cutting, wielding, dittoing, assembling and painting. The method ology involved the preliminary calculation of the total surface area of the two mili... Continue Reading

ABSTRACT It is generally known that cement id produced from limestone, mar/clay and gypsum by the following three basic process- wet semi- wet aid dry process. The cost of exploiting the limestone: the major raw material constitute about 50% of the production cost which results in the high cost... Continue Reading

ABSTRACT Car surfaces are vulnerable to scratches from environmental conditions, thereby prompting car users to visit car workshop for re-spray. This process does not usually bring permanent solution to scratches on car surfaces since they are often re-spray with non-self-healing paint. The aim of this work was to develop self-healing car paint.... Continue Reading

ABSTRACT The project dealt on the production of yam flour from yam chips. The yams were peeled and washed, 100grams samples coded sample A to G were subjected to two different drying conditions. Some were dried using the sun drying method while the others were dried through oven drying method kept at constant temperature of 500C, sodium... Continue Reading