Most Relevant Chemical Engineering Project Topics and Materials (Page 16)

Abstract It is of no doubt that one day, fossil fuels, which the whole world highly depends on, will come to a halt in a few decades to come. To this reason, researches have been geared towards alternative sources of energy: biodiesel, a form of renewable energy (energy that can be regenerated once used up), is one that has been made known and... Continue Reading

Cultivation of microalgae on municipal waste water  Extraction of the oil from the algae cells.  Production of biodiesel from the algae oil.  Characterization of the biodiesel produced.  Chapter 1 Introduction 1.1 Background 1.2 Statement of Problem 1.3 Aims and Objectives of Study 1.4 Significance of Study 1.5 Scope of Study Chapter 2... Continue Reading

Environmental pollution as a result of drilling and mining activities in areas where deposits of petroleum and oil are found, proved a great threat to the wellness of the fauna and flora as well as to the humans.  TABLE OF CONTENTS  Background of study literature review Oil pollution act of 1990 Diesel Chemical composition  Volatility of Diesel... Continue Reading

Oil obtained from orange peels and velvet tamarind nut by solvent extraction (n-hexane and acetone) using the soxhlet extractor were investigated as feedstock’s to determine some of the suitable parameters such as iodine value, saponification value, specific gravity, density, acid value and free fatty acid value, and their percentage yield that... Continue Reading

Kenaf reinforced polyethylene composites for ballistic protection was produced in this work. The samples of alkaline treated and silane-coupled non-woven matted kenaf fibers were cut to the required dimensions and oriented vertically and horizontally in combinations with a virgin high density polyethylene (VHDPE). The composite panels were... Continue Reading

ABSTRACT The potential advantage and application of the photocatalytic process using titanium dioxide as the photocatalyst to treat industrial waste water in UV irradiation has been reported. The aim of this work is to investigate the effectiveness of photocatalytic degradation using TiO2 in treating pharmaceutical waste water. Wastewater was... Continue Reading

ABSTRACT             The advent of sachet and bottled water has increasingly filled the gap in household water security. This research work was carried out to assess the quality of bottled and sachet water sold in Bauchi metropolis. Thirty (30) water brands consisting of twenty (20) sachet water brands and ten (10) bottled water brands... Continue Reading

This project contains details of Coal fired circulating fluidize boiler.The motivation of our project was to develop a method which is energy economical i.e. uses less energy owing to increasing energy issues. Process description, mass balance, energy balance, equipment design, and cost estimation of circulating fluidized bed boiler for combustion... Continue Reading

ABSTRACT The research titled extraction and characterization of watermelon seed oil was carried to investigate the effect that different drying methods, solvents and seed size would have on the quality and quantity of oil from watermelon ( Citrilus lanatus ) seeds. The watermelon seeds were removed from the pod and washed. The sample was weighed... Continue Reading

                                                                 ABSTRACT          Biomass is organic materials that are made from plants and animals. Biomass stored alot of energy from the sun. Biomass is renewable sources of energy which can grow more such as trees and crops,... Continue Reading

ABSTRACT The design of a 1000 tonnes per annum Shea butter plant was carried out using data obtained from literature. Assumptions were made, where experimental data were not available. The block diagram, process flow sheet, material and energy balance on the process was carried out and presented on this work. A total of six units were used in the... Continue Reading

ABSTRACTA study on the effects of post- harvest variables on the yield and quality of Shea butter wascarried out. The Shea nuts acquired from villages were divided into five batches with avillage/uncontrolled sample. Each batch was boiled at different time ranges (0, 15, 30, 45 and60) minutes. Each batch was dried through an oven drying method.... Continue Reading

Crude oil viscosity is an important parameter which is considered in both porous media and in pipeline channels. Estimating oil viscosity at various operating conditions of pressure and temperature is of great value to petroleum engineers. In petroleum and reservoir engineering, we are often faced with the analysis of processes which involve... Continue Reading

  ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension  of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding,... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material†is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the... Continue Reading

ABSTRACT This study has its theme as a utilization studies of Enugu coals with the view of studying its properties, classification, preparation storage etc comparing coals obtained from different locations. The Enugu coal is a sub-bitummous and non coking coal.  It is very rich in waxes and resins, thus it may be suitable for the production of... Continue Reading

ABSTRACT The project Analysis of Enugu Coal was done to determine the characteristic properties of Enugu Coal with particular emphasis on the proximate and ultimate analysis. Coal samples from the Enugu Coal (Onyeama) mine were obtained and pulverized.  The coal sample (pulverized) was subjected to proximate and ultimate analysis to determine its... Continue Reading

ABSTRACT In the construct of 2,000 litres capacity water reservoir galvanized  steel  sheet forms the tank and an angle iron rod forms the stand.  Two full length galvanized sheet were marked out and cut out to the required sizes.  The work stated by cutting the it gauges galvanized steel sheets of full length into geometrical dimensions of... Continue Reading

ABSTRACT Blender is an electric machine for size reducing soft food or liquid mixture.  Blender is some time called liquidizer consists of a glass jar or jug containing a steel blade assembly at the base driven by a small electric motor. Construction of blender was done based on the principle of size of reduction using electric motor as the major... Continue Reading

ABSTRACT A motorized mixer of 200 liters capacity was constructed to have the capability of mixing 200 liters of fluid during operation. The construction of the mixer involves the preliminary measures and calculations on the surface area of the metal sheet.  Some basic workshop practices was carried out during the construction such as the marking... Continue Reading

ABSTRACT This project (Construction Of A Simple Size Reduction Machine) It was constructed locally with the use of local materials and tools in I.M.T mechanical Engineering workshop.  The various parts of the equipment were constructed separately using mild steel before finally coupled.  During the construction, the conveyors and it’s... Continue Reading

ABSTRACT The purpose of the construction is aimed at producing heat energy for commercial use by turning liquid fuel(kerosene).the construction was successful by appropriate selection of engineering material favourably mild steel(blacksheet) and steel iron for special p2rts. The technological properties passed by the chosen mild steel are;... Continue Reading

ABSTRACT The aim of this project was to construct one office table and four chairs. In the course of this project the length of plank used was 12†and we used about 4 number (mahogany) of 1†thickness, ¾ plywood of 1 sheet of 1†thickness, as well as ¼†plywood of ½  and glue 1 tin wenner 1 rod, foam ½ sheet.  Fabrics... Continue Reading

ABSTRACT Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs.  Generally, interface is a boundary layer, so the boundary between two products when they are pumped in succession is known as interface. In Nigeria Petroleum Industries like NNPC (PPMC) make use... Continue Reading

ABSTRACT  This project is an equipment which been fabricated for the principle purpose of producing heat energy for commercial use by burning solid fuel like briquette.  The project which is the fabrication of briquette stove was made from preferentially selected engineering materials like mild steels of different gauge member and metallic rod.... Continue Reading