Project Topics and Materials - Page 835

a comparative study was done on the physico-chemical and antioxidant properties of some culinary herbs and local spices. Piper Guiness (Uziza), Xylopia aethopica (Uda), Monodora Myristica (Ehuru) and TrtraleuraTetraopera (Oshsho).  The proximate analysis of these spices  were done to determine their moisture content, ash... Continue Reading

CHAPTER ONE INTRODUCTION 1.1      Background of the study The search for efficient and effective delivery of instructions to Students has always been major concern of Science Educators. This is so as a result of... Continue Reading

 ABSTRACT             A study was carried out on the physico – chemical properties of fluted pumpkin seeds (Telferia occidentalis) flours.  The 1st two flour samples were obtained by boiling for 1 hr in 0.5% solution for Nacl, and .5% solution of Na2 S04 respectively. The 2nd two samples were obtained by soaking for 12 hrs in... Continue Reading

An electric popcorn machine is machine that is used to popcorn for human consumption. It uses electricity as it sources of energy, transfer it energy, that is used to pop the Corn. Also it has a stirrer, which rotate due to the convection of electrical energy from the source to mechanical energy in the motor, the stirrer tons the corn so... Continue Reading

This project has been fabricated with special economical needs for the small scale baking industries, wholesalers and distributors who import this type of baking oven from outside the country to supply the customers. Who wish to use it or those that cannot after gas oven can be used in baking any type of available within the tropics. It I... Continue Reading

CHAPTER ONE INTRODUCTION The project is a pre-requisite for the award of Higher National Diploma (HND) in Mechanical Engineering. The project “Design and fabrication a corn shelling machine” is indeed an essential one in a time like this when almost al human endeavour is embracing technology for efficiency and realiability. First a corn... Continue Reading

 ABSTRACT In this project, three alternative design solutions were considered for the foldable cam – bed. The authors utilize the local materials (with cost consideration) for the components. The merits and demerits of each of the alternative with respect to the considered group were also discusses and the solutions of the alternatives that... Continue Reading

            This project is concerned write the identification of those defects that are found in most of the drawing tables in the Mechanical Engineering drawing studio.             The report investigates the possible ways through which the mentioned above can be brought back to normal standard for usage ins the... Continue Reading

The design and fabrication of a reciprocating nail gasket is a new innovation in technology. The one in existence is manually operated. In which a punch that is adjacent to a die is mounted to the handle  which  is attached to the shaft. A helical spring that is incorporated to the shaft of the punch, helps the handle return to its... Continue Reading

            Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper.   Also studied were the manners of dependence of these parameters on prints impressed on sheets of varied... Continue Reading

This work is an attempt to evolve a means for statically and dynamical balancing of mechanical components. This will no doubt evolve greater success in ensuring sound fabrication of our local machine and ensuring that life span of such machine is prolonged since vibration will be reduced to the bearest minimum. Every wheel and its shaft... Continue Reading

Man’s imp act on global environment system especially in the area of dust extraction is now at a scale where it is disrupting.  These dust extractors varies in major ways. The environmental degration is, in turn contributing to health threat in this part of the globe.  Unfortunately most factories, workshops which suppose to posses... Continue Reading

            A machine for corn shelling is highly and greatly needed to consistency of usage of corn in local and international levels.             With regards to this indispensable needs, a corn shelling machine is designed which operates to remove the corn grains and leaving the cobs intact.... Continue Reading

TABLE OF CONTENT  CHAPTER ONE 1.1              Introduction                                                    1.2              Manual Digester                                             ... Continue Reading

            This project is constructed based on careful theoretical analysis of materials of chance and reasons for the selection of the materials.             The theoretical analysis of heat principles and temperatures of the different fervid which in solid stage should set in the mould were analyzed. The basic... Continue Reading

            To achieve the aim of producing a functional and efficient wood lathe machine.  We analyzed and as well synthesized the different possible design solutions and concepts.  We carried out the analysis of different component part of the machine to determine their suitable dimensions based on loading and stresses due... Continue Reading

This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used in... Continue Reading

This machine is meant for sealing and cutting of nylon bag of different sizes. This machine is operated with electrical system. This machine can cut and seal nylon of different sizes. It also comprises of materials as follows: Mechanical and Electrical section Mechanical section include the frame structure, lever and the pedal mechanism.... Continue Reading

            Mechanical engineering department of the named institute has many non operational machines sequel to this fact maintenance which resulted to non development and non maintenance of the institute community at large.             By this fact the project (mechanical lawn mower) was constructed and design to... Continue Reading

            This research work was carried out to examine the influence of communication equipment on the efficiency of the secretary with particular reference to Nigerian Breweries Public limited company NBL/Ama Green Field 9th mile corner Enugu.             The theoretical frame work for this study was based on... Continue Reading

The aim of this study is to find out the impact of the internet on secretarial profession.  This research covers the selected business organizations in Enugu metropolis. In this research, the related literature were reviewed. The population used for this study were ninety secretaries which were picked from selected seven business... Continue Reading

ABSTRCAT             The study is aimed at finding a survey of the factors responsible for students poor performance in shorthand in polytechnics in Enugu.             In search of the required information, the researcher administered questionnaires to 100 respondents that made up the population for this study.... Continue Reading

PROPOSAL             Proposal page simply means the summary of the fist three chapters, introduction, literature review and research methodology.             Project Topic: The effect of secretarial job design in FRCN             Job design concerns the content functions and relationship of job that are direct... Continue Reading

The topic of this research is the contributions of modern office equipment. In the advancement of secretarial profession. The study was restricted to Anammco and Emenite Plc. Emene, near Enugu Urban.             To conduct the study, questionnaire structured in two phases was used as the instrument for collecting data. The... Continue Reading

            The main aim of this project is to find out the effects of students industrial work experience scheme to the students in tertiary institutions in Federal Polytechnic Oko in Anambra State.             The researcher considered whether students actually receive practical training in industries and how far... Continue Reading