Most Read Electrical Engineering Project Topics and Materials (Page 12)

Showing 276 - 300 of 530

276) DESIGN AND CONSTRUCTION OF A COMPUTER BASED CONTROL OF ELECTRICAL APPLIANCES

INTRODUCTION This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault... Continue Reading

277) CONSTRUCTION OF RADIO FREQUENCY GSM SIGNAL JAMMER

Abstract A wireless signal jammer is a device which blocks transmission by creating interference. This wireless signal jammer can be categorized into the Radio Frequency (RF) jammer and GSM jammer. A Radio Frequency jammer is a device used to disrupt or prevent communication via a broadcasted RF signal. It is an RF and GSM frequency disrupter... Continue Reading

278) CONSTRUCTION OF A BATTERY CHANGER USING SILICON CONTROLLED REGULATOR (SCR)

ABSTRACT The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed... Continue Reading

279) INTEGRATION OF DISTRIBUTED GENERATION (DG) OF ELECTRIC POWER SUPPLY

Adding to the requirement and need for power supply for day to day activities, it is therefore a necessity to design the power system to maintain minimal technical losses in the network, because most of our system component lack sufficient reactive power ability, this mean that the penetration of distributed generation (DG) will give way to reduce... Continue Reading
  • Type:Project
  • ID:ELE0190
  • Pages:108

280) WASTES AND SEWAGE AS A SOURCE OF ELECTRICITY GENERATION

ABSTRACT Waste and residuals are undeniably part of the human society. The accumulation of these materials and the “throw away” philosophy results in many environmental and health issues and safety hazard problems prevent sustainable development in terms of resource recovery and recycling of waste materials. The carbon sources in the waste can... Continue Reading

281) PATIENT HEARTBEAT AND TEMPERATURE MONITOR

Abstract Heart beat rate means the number of heartbeats per unit time, usually expressed as beats per minute (bpm). The human heart pounds to pump oxygen rich blood to the muscles and carry cell waste products away from the tissues. Heartbeat rate can vary according to the demand of the muscles to absorb oxygen and excrete carbon dioxide changes... Continue Reading

282) CONSTRUCTION OF 150 WATTS 162 AUDIO LOUDSPEAKER

ABSTRACT Audio loudspeaker (output transducer) is on of the most essential and powerful device used in telecommunication system. This is device capable of converting electrical signal into sound and vice versa. It is made up of few time of non-magnetic wire wound on a light cylindrical former that is mounted so that it can move freely insides the... Continue Reading

283) CONSTRUCTION AND IMPLEMENTATION OF 6V ECHARGEABLE LAMP

ABSTRACT Researchable lamp is a source of light that is generated from a D.C sources of supply this D.C sources is a battery that can also way be charged when it current and voltage ruse I decided to work on this as my project because its importance. It is very portable and help the a lot during night reading It also serves as an immanency sources... Continue Reading

284) DESIGN AND DEVELOPMENT OF COMPUTER BASED TEST SYSTEM TO FACILITATE E-EXAM.

ABSTRACT The purpose of this project was to design and develop a Computer Based Testing (CBT) system in order to facilitate the process of conducting e-examinations especially in tertiary institutions. There is a growing need to find an easy and effective way to carryout continuous assessments for the increasing population of students. The CBT... Continue Reading

285) DESIGN AND CONSTRUCTION OF 2KVA INVERTER

ABSTRACT This project presents the design and construction of a DC to AC inverter system. It is designed to meet up with the power demand in the offices/homes in the absence of power supply from National Supply Authority.  It is designed in such a way that it will take up to 12V DC from battery and inverts it to an output of 220V, 50Hz AC. It... Continue Reading

286) EXERGY ANALYSIS OF COMBINED CYCLE POWER PLANT (GARRI”2” 180 MW)

ABSTRACT In recent years the entire world is a warring about energy resources limitation, specifically Sudan country confronts critical crises in fossil fuel resources and yet more of electricity energy producing from fired thermal power plants. One from these plants Garri”2” combined cycle producing about 180MW. Exergy analysis in the light... Continue Reading

287) A FAULT DETECTION AND PROTECTION SCHEME FOR A 200 MVA TRANSFORMER USING FUZZY LOGIC

ABSTRACT Condition monitoring of Electrical power equipment has attracted considerable attention for years. The aim of this work is to use Fuzzy logic (FL) Tool Box in building a simulation system that will diagnose all kinds of incipient faults, phase to phase fault and overloading in a transformer and monitor its conditions. Current and rate of... Continue Reading

288) DESIGN AND CONSTRUCTION OF A POWER INVERTER

ABSTRACT Power inverter is an electrical appliance that can be used with DC battery as an alternativesource of energy supply in the event of power failures and energy crisis. It is cheap, clean,very conducive and silent when in operation and a very reliable source of power supply as togenerator. Modern research and technologies have shown that... Continue Reading

289) DESIGN OF AN ELECTRONIC SIREN CIRCUIT

Siren is a device that produces loud noise. They are the means communication. Sirens  can be seen in emergency vehicles such as police cars, ambulances and fire trucks. Generally, sirens are used as indication or warning. There are different circuits to  produce different sirens.  The word siren first originated in Greek mythology and was also... Continue Reading

290) THE DESIGN AND CONSTRUCTION OF AN INVERTER

TABLE OF CONTENTS Title Page Certification Page Acknowledgements Dedication  CHAPTER ONE:INTRODUCTION  1.1Definition of Term  CHAPTER TWO:TRANSFORMER FUNDAMENTALS   CHAPTER THREE:DESCRIPTION OF COMPONENTS  3.1Resistors  3.2Capacitors 3.2.1Types of Capacitor 3.3Semi-Conductor Diode  3.4Transistors  3.4.1Bipolar Transistor  3.5Field Effect... Continue Reading

291) DESIGN AND INSTALLATION OF 200 WATT SOLAR POWER SYSTEM

ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading

292) HYPERTHERMIC TREATMENT OF BREAST CANCER USING BIOMEDICAL ANTENNA

Anatomical variation in the human body presents a complex challenge to design a universal antenna for all. The presence of the human body in close proximity to the antenna also presents a challenge as the near field strongly couples with a lossy medium. Other challenges include design of an antenna that is small in size without affecting its... Continue Reading

293) DESIGN AND CONSTRUCTION OF 36W AUTOMATIC SOLAR STREET LIGHT USING SOLAR PANEL, CHARGE CONTROLLER, LED AND WITH BATTERY

CHAPTER ONE INTRODUCTION 1.1Background Information Electricity is a general term comprising of a variety of phenomena resulting from the presence and flow of electric charge. These include many phenomena, such as lightning, static... Continue Reading

294) DESIGN AND CONSTRUCTION OF FIRE ALARM

ABSTRACT  This project the design an construction of fire alarm was carried out with deep intensive and extensive research work my aim and objective in the price of work is to produce a standard device or electronics that will inform the security about a fire outbreak in the company or house for a quick reaction/action. In this project I shade... Continue Reading

295) MODELLING AND SIMULATION OF LEAKAGE-INDUCED PRESSURE DROPS ALONG OIL AND GAS PIPELINES

ABSTRACT This research work on “Modelling and Simulation of Leakage-Induced Pressure drops along oil and gas pipelines tends to develop flow equations that can detect and localize leakages in oil and gas pipelines by modifying the Darcy-weisbach equation for liquid/oil flow, and the Panhandle B equation for natural gas flow in pipelines. These... Continue Reading
  • Type:Project
  • ID:ELE0298
  • Pages:135

296) DESIGN AND IMPLEMENTATION OF AN AC/DC POWER HARVESTING USING HUMAN FOOT STEP

ABSTRACT As the demand of energy is increasing day by day, so the ultimate solution to deal with these sorts of problems is just to implement the renewable sources of energy Humans are using the renewable energy which are solar, wind etc. but we still could not satisfy our power needs, because of that we have to generate electricity through each... Continue Reading

297) DESIGN CONSTRUCTION AND IMPLEMENTATION OF A TOUCH SENSITIVE SWITCH

ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and... Continue Reading

298) DESIGN AND IMPLEMENTATION OF GSM BASED INDUSTRIAL PROCESS MONITORING AND CONTROL SYSTEM

TABLE OF CONTENTS DECLARATION........................................................................................................................i APPROVAL..............................................................................................................................ii MR. ADABARA... Continue Reading

299) SPEED CONTROL OF MARINE DIESEL ENGINE SELF-TUNING BASED ON FUZZY PID CONTROL AND GENETIC ALGORITHM PID

The mathematical model of diesel engine and its speed regulation system are presented and computer simulation is conducted in Matlab software. Simulation results verify that the proposed method improves the control accuracy of speed of diesel engine. A fuzzy PID hybrid controller and a Genetic Algorithm PID of parameter self-adjusting is put... Continue Reading

300) DESIGN & IMPLEMENTATION OF AN INDUSTRIAL HEALTH AND SAFETY MONITORING AND PREVENTION SYSTEM USING RADIO FREQUENCY TECHNOLOGY

TABLE OF CONTENTS DECLARATION ..................................................................................................................i APPROVAL.........................................................................................................................ii... Continue Reading
Need help with your Electrical Engineering Project Topic? Click here to request assistnce or reach us on + 234 813 0686 6500
whatsappWhatsApp Us