Project Request: solar windmill power generator

More Details
Department: computer engineering
Level :
Status: APPROVED
Delivery :Soft Copy

Related Works

This project covers the design and construction of a power generating windmill. The designs was carried out based on long-term available wind data of bida at 10m above the ground level. The average wind speed for Bida is 5.24m/s and rated turbine wind speed is 6.29m/s. The design of each components of the system were carefully constructed in a... Continue Reading
This project covers the design and construction of a power generating windmill. The designs was carried out based on long-term available wind data of bida at 10m above the ground level. The average wind speed for Bida is 5.24m/s and rated turbine wind speed is 6.29m/s. The design of each components of the system were carefully constructed in a... Continue Reading
CHAPTER ONE INTRODUCTION 1.1       Preamble A power inverter, or inverter, is an electronic device or circuitry that changes direct current (DC) to alternating current (AC). ( The Authoritative, 2000 ). The input voltage, output voltage and frequency, and overall power handling depend on the design of the specific device or circuitry. The... Continue Reading
  TABLE OF CONTENTS DECLARATION i DEDICATION ii COPYRIGHT iii ACKNOWLEDGEMENTS iv ABSTRACT v LIST OF TABLES vii LIST OF FIGURES viii LIST OF ACCRONYMS AND ABBREVIATIONS ix OPERATIONAL DEFINITION OF TERMS x INTRODUCTION 1 1.0 Background of the Study 1 1.2 Solar Power System 2 1.3 Operating Principle of the DSTATCOM 3 1.4. Modelling of PV Array 5... Continue Reading
L (A CASE STUDY OF COMPUTER SCIENCE ND SOFTWARE LAB) CHAPTER ONE INTRODUCTION 1.1   BACKGROUND TO THE STUDY The use of renewable energy increased greatly just after the first big oil crisis in the late seventies. At that time, economic issues were the most important... Continue Reading
  TABLE OF CONTENTS DECLARATION    i DEDICATION    ii COPYRIGHT    iii ACKNOWLEDGEMENTS    iv ABSTRACT    v LIST OF TABLES    vii LIST OF FIGURES    viii LIST OF ACCRONYMS AND ABBREVIATIONS    ix OPERATIONAL DEFINITION OF TERMS    x INTRODUCTION    1 1.0 Background of the Study    1 1.2 Solar Power System    2... Continue Reading
CHAPTER ONE INTRODUCTION The evolutionary trend in industrial electronics and automation has engulfed all parts of the world and proved more challenging to as third world like Nigeria. Regarding the milestone, it was decided to make the choice of project research on the design and implementation of an automatic 3 - phase change – over with... Continue Reading
(A CASE STUDY OF COMPUTER SCIENCE LABORATORY) ABSTRACT This Project entitled “DESIGN AND IMPLEMENTATION OF SOLAR POWER BANK” was designed to expose the participants to the practical skills needed in designing a solar power bank. The specification of the solar system is: Solar Panel, Mounting... Continue Reading
ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading
CHAPTER ONE INTRODUCTION The quest to satisfy our need for stable power supply in Nigeria has driven most Nigerians into an ardent search for alternative renewable power sources. One of such major renewable power source in use is solar energy, which is energy obtained from the radiation of the sun. To obtain electrical power from the sun, four key... Continue Reading
ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller.... Continue Reading
ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading
The aim of the project is to design a renewable energy system that can meet the current and  projected electricity demands for the island of Great Cumbrae. This should be achieved by  providing a stable electricity output and the meet the calculated total annual base load supply of  11.29 GWh. In addition to providing a stable supply of... Continue Reading
Table of Contents 1. Introduction 2. Electricity Demand 3. Wind Power System 4. Floating Solar Photovoltaic (PV) System 5. Electricity Storage Systems ____ 6. Site Choice 7. Planning Permission Statement 8. Environmental Impact Assessment _ 9. Project Plan 10.... Continue Reading
ABSTRACT This work is concerned with the features, analysis and design of a stand-alone solar energy based power supply with maximum power point tracking (MPPT) scheme. The features and operations of various types of solar cells and panels and the performance characteristics under varying temperature and irradiance conditions are studied.... Continue Reading
ABSTRACT Automatic gate is one of most usefully thing to use in companies, colonies, collages, homes, and schools. There is some type to operate a gate such as a sliding on screw or on rack and pinion, piston operated, rotary. Design is available for some type of operation and it is most costly also When installation and maintenance cost is not... Continue Reading
CHAPTER ONE INTRODUCTION 1.1Background Information Electricity is a general term comprising of a variety of phenomena resulting from the presence and flow of electric charge. These include many phenomena, such as lightning, static... Continue Reading
CHAPTER ONE INTRODUCTION 1.1 Background Information Electricity is a general term comprising of a variety of phenomena resulting from the presence and flow of electric charge. These include many phenomena, such as lightning,... Continue Reading
Abstract This project work centered on construction of 12V/10A solar charge controller that is needed in photovoltaic system to safely charge regulate and discharge of sealed lead acid battery through DC load. Solar charge controller is devices that regulate solar photovoltaic power and prevent overcharging, over discharging or overflow of current... Continue Reading
Abstract This project work centered on construction of 12V/10A solar charge controller that is needed in photovoltaic system to safely charge regulate and discharge of sealed lead acid battery through DC load. Solar charge controller is devices that regulate solar photovoltaic power and prevent overcharging, over discharging or overflow of current... Continue Reading
whatsappWhatsApp Us