Project Request: Design and construction of ground nut oil extraction

More Details
Department: Agric Education
Level : HND
Status: APPROVED
Details/Dead Line : Design and construction of groundnut oil extraction and extruder

Delivery :Soft Copy

Related Project Topics

REHABILITATION OF ROAD LINKING UMUEKULUMMIRI STREET TO IMT AWARNESS GROUND JUNCTION IMT CAMPUS III ENUGU ABSTRACT This project entitled “Rehabilitation of Road” is aimed at investigating the causes of failure on the road linking Federal Secretariat, IMT Civil soil lab to Industrial Centre IMT... Continue Reading
CHAPTER ONE INTRODUCTION The word wax describes a large variety of substances of plant and animal origin, as well as man made products which are mostly petroleum derivatives. However, natural waxes are not single substances, but a mixture of various of long-chain... Continue Reading
ABSTRACT The estimation of vitamin C in Tangerine Juice was investigated, the results obtained using titrimetric method shows that one tangerine fruit juice contains approximately 10mg of vitamin C content, and the 19 fruits sample... Continue Reading
  • Type:Project
  • ID:CHM0003
  • Department:Chemistry
  • Pages:49
  • Chapters:5
  • Methodology:Scientific Method
  • Reference:YES
ABSTRACT The estimation of vitamin C in Tangerine Juice was investigated, the results obtained using titrimetric method shows that one tangerine fruit juice contains approximately 10mg of vitamin C content, and the 19 fruits sample... Continue Reading
  • Type:Project
  • ID:CHM0002
  • Department:Chemistry
  • Pages:49
  • Chapters:5
  • Methodology:Scientific Method
  • Reference:YES
ABSTRACT An inverter is an electronic device that converts direct current (DC¬) to alternating current (AC) the converted Ac can be at any required voltage and frequency with the use of appropriate transformers, switching and control circuit. It’s simple... Continue Reading
ABSTRACT Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper. Also studied were the manners of... Continue Reading
ABSTRACT The design and construction of s refrigerating unit is handled from the knowledge of the working principles of laws of thermodynamics. The size of the containing vessel i.e the case as established to be of 45cm by 32 cm in dimension. The... Continue Reading
ABSTRACT This work is aimed at designing and fabricating a spin dryer which can be used in drying spent grains after brewing. This will no doubt save considerable human labours and time wastage involved in conventional method of drying the spent grains by... Continue Reading
ABSTRACT This work is an attempt to evolve a quicker and easier method of achieving cylindrical shape object from a work price. This will no double save considerable human labour and time wastage involved in traditional manual method of carving. To... Continue Reading
ABSTRACT This project is constructed based on careful theoretical analysis of materials of chance and reasons for the selection of the materials. The theoretical analysis of heat principles and temperatures of the different fervid... Continue Reading
ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector. In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a... Continue Reading
ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector. In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a... Continue Reading
DESIGN AND CONSTRUCTION OF A METALLIC BOOK SHELF ABSTRACT This project aims at designing and constructing a book metallic shelf hose capability will be to contain different standard sizes of books at minimum paces. What is taken into consideration in this project are the cost of its production,... Continue Reading
ABSTRACT An audio AMP is basically a system which is used as a means of increasing the level of sound or audio signals for maximum use. A public address system consists basically of microphone, Amplifier and speaker(s) to facilitate the... Continue Reading
ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator”... Continue Reading
CHAPTER ONE INTRODUCTION 1.1 THE BACKGROUND Welding is a way of heating pieces of metal using electricity or a flame so that they melt and stick together. It can simply be defined as the process of joining two or more pieces of metal... Continue Reading
DESIGN AND CONSTRUCTION OF 1000VA AUTOMATIC VOLTAGE REGULATION ABSTRACT The design and construction of 1000VA Automatic Voltage Regulator is made to power our Electrical and Electronic devices, supplying them with the normal output voltage which ranges from 100V- 240v irrespective of the constant... Continue Reading
ABSTRACT This project is design and construction of a sound detector with alarm system was done primarily to detector sound. It can be use in industrial and domestics. It employ four discreet stages with power supply which power the... Continue Reading
ABSTRACT The design and fabrication of a reciprocating nail gasket is a new innovation in technology. The one in existence is manually operated. In which a punch that is adjacent to a die is mounted to the handle which is attached to the... Continue Reading
ABSTRACT Distance measurement plays a vital role in engineering, science and business. The distance is always measured between two points. Generally distance measurement is possible only by making contact with the target whose... Continue Reading
  • Type:Project
  • ID:PHY0004
  • Department:Physics
  • Pages:67
  • Chapters:5
  • Methodology:Nil
  • Reference:YES