+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE STABILIZER

  • Type:Project
  • Chapters:6
  • Pages:32
  • Methodology:Scientific
  • Reference:YES
  • Format:Microsoft Word
(Electrical Engineering Project Topics & Materials)

ABSTRACT

In the world today, the use of power supply in electronics equipment and gadgets has increased and it is still increasing. These power supplies are not stable as required by these electronics.
This arise the need for the power stabilization as to overcome this problem 
This project handles this problem very well. Some recommendations were also made on this topic and student and users of electronics equipment will find them useful.

TABLE OF CONTENTS
CHAPTER ONE
1.0    Introduction
CHAPTER TWO
2.0    Literature Review
2.1    The aims/purpose
2.2    Stages in the development of voltage stabilizer
2.3    Stabilizer grading
2.4    Application

CHAPTER THREE
3.0    Basic Theory of Components Us ed
3.1    Transistors
3.2    Diode
3.3    Resistor
3.4    Relay
3.5    Zener diode
3.6    Capacitor
3.7    Transformer
3.8    Fuse
3.9    Other materials us ed
CHAPTER FOUR
4.0    Design, Construction and Operation of the Stabilizer
4.1    Design/Construction
4.2     The Transformer Stage
4.3    Control Stage
4.4    The Relay Stage
4.5    Operation
4.6    Transformer Stage
4.7    Control Stage
4.8    Relay Stage
CHAPTER FIVE
5.0    Discussion, Conclusion and Recommendation
5.1    Discussion
5.2    Conclusion
5.3    Recommendation
CHAPTER SIX
6.0    Cost Analysis, References
6.1    Cost Analysis
6.2    References
CHAPTER ONE

INTRODUCTION
In Nigeria and some other parts of the world today, the electricity power supply to consumers (at homes and industries) are not maintained at a stipulated voltage say 240 volts. But the electronics gadgets and some other power operated machines, that we use in our homes, offices and industries requires power with constant or nearly constant voltage for their efficiency, and to avoid damage by the voltage.
Voltage stabilizer is an electronic control circuit or device that is capable of providing a constant or nearly constant output voltage even when there is variation in load or input voltage as low as 90 volt can be boast up to 240 volt by stabilizer at output stage without any voltage fluctuation.

DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE STABILIZER

Share This

Details

Type Project
Department Electrical Engineering
Project ID ELE0120
Price ₦3,000 ($20)
Chapters 6 Chapters
No of Pages 32 Pages
Methodology Scientific
Reference YES
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Electrical Engineering
    Project ID ELE0120
    Price ₦3,000 ($20)
    Chapters 6 Chapters
    No of Pages 32 Pages
    Methodology Scientific
    Reference YES
    Format Microsoft Word

    Related Works

    ABSTRACT This project proposes a new type of voltage regulator based on single-phase converter otherwise known as transformerless AVR that compensates wide range voltage variations. This is not only capable of compensating variations at a much higher bandwidth but also does not experience mechanical wear down and is cost effective. The proposed... Continue Reading
    DESIGN AND CONSTRUCTION OF 1000VA AUTOMATIC VOLTAGE REGULATION ABSTRACT The design and construction of 1000VA Automatic Voltage Regulator is made to power our Electrical and Electronic devices, supplying them with the normal output voltage which ranges from 100V- 240v irrespective of the constant voltage and current fluctuation, failure and... Continue Reading
    ABSTRACT This project is all about Automatic Voltage Regulator (AVR), and is a circuit that monitors the input voltage at any point and display the regulated voltage level on the analog meter. It is mainly for electrical/electronic system that is delicate to abnormal voltage level. It is usually connected as an intermediary between voltage supply... Continue Reading
    ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching stages and then... Continue Reading
    ABSTRACT Automatic voltage inverter is an important area in power system engineering. It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer. The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then from power... Continue Reading
    ABSTRACT Despite all attempt of the federal government to have not only an uninterrupted power supply for all cities in Nigeria, but a voltage that is inconformity with the recommended 220/230v for domestic consumption for example. The NEPA Plc is facing some difficulties in generating, transmitting and distributing the required voltage... Continue Reading
    ABSTRACT This project is he design and construction of a voltage inverter system with trickle charging system. This device is design to provide power supply for the need of offices, household etc. In absence of NEPA power supply. It would also prevent harm to our appliances caused by power holding company LTD (NEPA) Random power outage . TABLE OF... Continue Reading
    ABSTRACT This project is he design and construction of a voltage inverter system with trickle charging system. This device is design to provide power supply for the need of offices, household etc. In absence of NEPA power supply. It would also prevent harm to our appliances caused by power holding company LTD (NEPA) Random power outage . TABLE OF... Continue Reading
    ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading
    ABSTRACT This is a technical report presented on the design and construction of an Automatic Three Phase Selector.         In the construction work, an ordinary level knowledge of electronics principles are observed. We aimed at presenting a practical aspect of the subject and then providing the argument necessary for a thorough... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us