PREPARATION OF SOAP USING DIFFERENT TYPES OF OILS AND EXPLORING ITS PROPERTIES

  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0134
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 38 Pages
  • Format: Microsoft Word
  • Views: 7.9K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
           PREPARATION OF SOAP USING DIFFERENT TYPES OF OILS AND EXPLORING ITS PROPERTIES
ABSTRACT

Soaps are the sodium salts or potassium salts of stearic acids or any other fatty acids. They are prepared by the saponification process, which is, reacting the oil which contain triglycerides with caustic soda (NaOH) to give the soap. However different oils have different composition of fatty acids which are responsible for different properties of soaps made out of them. In the present work 5 different types of oils are taken. They are blended in various ratios to prepare 14 different samples of soap. Different properties of these samples were analyzed to see which soap is the best one. The cleansing and lathering properties of all samples were compared. The blend of coconut oil and castor oil at 3:1 ratio is found out to be the best with 76.8% of TFM and 89.46% of yield. The best blend is analyzed for various properties and they were compared with that given in the literature. The saponification values, iodine values of coconut oil and castor oil were found out and these values were also found for the blend. It was found that the blend was having SAP value of 230.4 and iodine value of 40 which are higher than the individual values. Thus soap prepared using blend of both these oils has better properties than the soaps prepared by individual oils.
      CONTENTS         
      Chapter 1    Introduction         
Chapter 2    Literature Review         
2.1    Semi Boiled Process         
2.2    Full Boiled         
2.3    Cold Process         
2.4    Different types of soap making oils         
2.5    Castor Oil         
2.6    Olive Oil         
2.7    Neem Oil         
3.1    Coconut Oil         
Chapter 3    Materials and Methods         
3.1    Materials Required         
3.2    Methodology         
3.2.1    Preparation of Soap         
3.2.2    Comparing different         
     properties of soap with detergent         
3.2.3    Blending of Oils         
 3.2.4    Calculation of TFM    
3.2.5    Calculation of free alkali    
3.2.6    Analysis of the best blend    
3.2.7    Saponification Value    
3.2.8    Iodine Value    
3.2.9    Unsaponifiable Matter    
3.2.10    Acid Value    
Chapter 4    Results and Discussion    
4.1    Comparison of soap and detergent    
4.2    Properties of soap after blending of oils    
4.3    TFM values of soaps    
4.4    Analysis of the best blend    
4.5    Saponification Values    
4.5    Iodine Values    
4.6    Unsaponifiable Matter    
4.7    Acid Value    
Chapter 5    Conclusion    
Chapter 6    References    
     List of Tables         
   1    Composition of coconut oil   
2    Yield of soap using individual oils   
3    Properties of soap versus detergent  
4    Moisture and Hardness of soap samples from   individual oils         
5    Yield and pH values of soap samples from blending of   oils         
 6    Lathering and cleansing power of soap samples from       
     blending of oils         
  7    Moisture and Hardness of soap samples from blending
     of oils         
8    Total fatty matter of best blends of oils  
9    Saponification value of the oil blend  
10    Iodine value of the oil blend 
 11    Unsaponifiable matter       
    12    Acid Value of the oil blend    
      CHAPTER ONE
 Introduction:
A soap is a salt of a compound, known as a fatty acid. A soap molecule has a long hydrocarbon chain with a carboxylic acid group on one end, which has ionic bond with metal ion, usually sodium or potassium. The hydrocarbon end is non polar which is highly soluble in non polar substances and the ionic end is soluble in water. The structure of the soap molecule is represented below:
The cleaning action of soapsbecause of their ability to emulsify or disperse water-insoluble materials and hold them in the suspension of water. This ability is seen from the molecular structure of soaps. When soap is added to water that contains oil or other water-insoluble materials, the soap or detergent molecules surround the oil droplets. The oil is, dissolved in the alkyl groups of the soap molecules while the ionic end allows it to be dissolved in water. As a result, the oil droplets are to be dispersed throughout the water and can be washed away.
A number of things affect the soap-making process and the quality of this soap produced. The characteristics of this soap depend on the quality of oil, and the amounts of the caustic soda and water used to make it. The speed of the reaction between the oil and the caustic soda is influenced by free fatty acid content of the oil, the heat of the components before mixing, and how vigorously the mixing is to be done. Free fatty acid contents, vigorous mixing, and heat, speed up the given soap-making process.
Castile soap: a mild soap originally made in Spain with pure olive oil. Today many “castile” soaps are made with other vegetable oils. Castile is agood cleanser, producing a rich lather. Cream soaps: soaps containing cold cream materials, and moisturizers. Cream soaps are good for dry and delicate skin
Deodorant soap are soaps to which antibacterial agents have been added to reduce odor-causing bacteria. Floating soaps: soaps which have air bubbles incorporated have low density. This causes the bar to float.Hypo-allergenic soaps: Mild formula soaps, low in potent irritants. They generally produce a poor lather.
Milled soaps: these are the most commonly used, mass produced soaps. Milling is referred to the mixing of colour and soap flakes.
Oatmeal soap: A rough textured soap to which oatmeal has been added as a mild abrasive and lather. Good for and normal skin.
A good soap is biodegradable when it does not contain chemicals that cannot be made to their natural elements. Neither does it contain chemicals that can be harmful to the environment or cause undue destruction to the environment.
•         A good soap gets dissolved easily and remove stains from the clothes, human skin or any material being cleaned.
•         It gets dissolved in water and produces enough suds.
•         It gives a clear and sparkling kind of cleanliness.
•         It gives a pleasant smell.
•         A good soap does not leave sticky traces on the clothes or on the skin.
•         It has a good color that is even and does not streak.
•         It disinfects and kills germs.
•         It does not damage the fibers or textiles.
 
PREPARATION OF SOAP USING DIFFERENT TYPES OF OILS AND EXPLORING ITS PROPERTIES
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0134
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 38 Pages
  • Format: Microsoft Word
  • Views: 7.9K
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0134
    Fee ₦5,000 ($14)
    Chapters 5 Chapters
    No of Pages 38 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT   Organizational justice is an essential component and predictor of successful organizations. Organization that is fair and just in its procedures, policies, interactions and distribution systems, employees of that organization give better response to the organization in terms of their positive behaviours and productivity thus the main... Continue Reading
    ABSTRACT Preparation of Local Soap involves the se of wood ash from the flowering plant of Daniello, Oliveri (Agba) Isoberllima doka (Achi), Parkia Clappertonwna (Ugba) and Eleasis guineensis (Nkwu) as the source for the caustic alkali were compared for performance.  The woody tissue of the local trees were burnt at the temperature of 250 \'... Continue Reading
    Abstract The optimization of biodiesel production from two non-edible oils and studies of their fuel and biodegradability properties was carried out. The two oil feedstocks (Yellow oleander and Castor oils) were extracted from their seeds using an oil expeller and their physicochemical properties such as iodine value, moisture content,... Continue Reading
    CHAPTER   ONE 1.0      INTRODUCTION 1.1      BACKGROUND Soap is the earliest detergent know to man and apparently was first made by the Romans from animal fats and oil and wood ash which is an alkali that contains potassium carbonate, sodium, potassium hydroxide called potash leached from the wood ash (Robert, 1994).  It is also an... Continue Reading
    ABSTRACT The construction of soap cutting table, mould and cutters became inevitable as it’s importance in our industries and society could not be over emphasized. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    ABSTRACT The construction of soap cutting table, mould and cutters became inevitable as it’s importance in our industries and society could not be over emphasized. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    ABSTRACT Two medicated soaps and one local soap were investigated for their antibacterial activities against  Staphylococcus aureus . Identification of the bacteria species was by standard microbiological techniques which included colonial examination, gram staining, and biochemical testing. Minimum inhibitory and minimum bactericidal activities... Continue Reading
    ABSTRACT This thesis aimed at the production of biolubricant from vegetable oils. The first stage produced methyl ester of the oil and in the second stage; the methyl ester was transesterified with Trimethylolpropane (TMP) in a ratio of 3.5:1 at 1500C to produce the biolubricant. The pour points biolubricant and its blend were significantly... Continue Reading
    ABSTRACT The topic of this project is the “selection of lubricating oils for varied engines performance”. The aim is to specify the adequate lubricating oils for different engines. Using some equipment like hydrometer, flash point tester, and visometer, the proportion of lubricating... Continue Reading
    INTRODUCTION Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work: digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us