+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

THE FABRICATION FOR A SET OF SIEVES AND SAKER

  • Type:Project
  • Pages:45
  • Format:Microsoft Word
(Chemical Engineering Project Topics & Materials)
ABSRACT

The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component parts of the sets of sieve and their dimensions are as follows:
Height of sieve 5.5cm
Number of sieves 7
Diameter of sieve 13.5cm
Shape of sieve circular
Height of sieve set 44cm
In fabricating this set of sieves, some factors were taken into consideration and they are:
The capacity of the sieve.
The type of mixture that can be filtered in it.
The types of properties and composition of the mixture.
The type of material to be used for fabrication of the sieve and shaker.
The mechanism of the filtration process and also,
The cost, which is the determinant, factor in fabrication of any equipment.
These factors help greatly in the fulfillment of the objective of this project study. And after fabrication the projects were tested and seem to be working very efficiently with a reasonable separation of particle and cut diameter.
Using the above dimensions, the following fabrication procedures were undertaken, layout, cutting, drilling, welding, filling sand papering, washing and painting, drying assembling.
Finally,  the set of sieves and shaker were subjected to the process of washing, painting and drying.


TABLE OF CONTENT

Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of content

CHAPTER ONE
1.0 INTRODUCTION

CHAPTER TWO
2.0 LITRATURE REVIEW
2.1 Model
2.2 Screening
2.3 Types of screens
2.4 Screen surface
2.5 Factors in selecting screen equipment
2.6 Method of feed

CHAPTER THREE
3.0 MATERIAL OF CONSTRUCTION
3.1 Aluminum and aluminum alloy
3.2 Carbon and low alloys steel
3.3 Corrosion 
3.4 Contact or galvanic corrosion

CHAPTER FOUR
4.0 FABRICATIONAL PROCEDURE
4.1 Layout
4.2 Cutting
4.3 Drilling
4.4 Welding
4.5 Filling
4.6 Sand papering
4.7 Washing and painting
4.8 Drying
4.9 Assembling

CHAPTER FIVE
5.0 OPERATION AND MANTENANCE
5.1 Function of some parts of the electrically vibrated screen.

CHAPTER SIX
6.0 RECOMMENDATION AND CONCLUSION
6.1 Costing 
REFERENCE.

THE FABRICATION FOR A SET OF SIEVES AND SAKER

Share This

Details

Type Project
Department Chemical Engineering
Project ID CNG0274
Price ₦3,000 ($9)
No of Pages 45 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0274
    Price ₦3,000 ($9)
    No of Pages 45 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The project is about fabrication of wheel-barrow, which is fabricated in Mechanical Engineering workshop in Institute of Management and Technology, Enugu. The report comprises seven chapters. Chapter one is about the introduction of the wheel. Chapter two is about the literature review, chapter three is about the material selection and... Continue Reading
    ABSTRACT In this project, three alternative design solutions were considered for the foldable cam – bed. The authors utilize the local materials (with cost consideration) for the components. The merits and demerits of each of the alternative with respect to the considered group were also discusses and the... Continue Reading
    ABSTRACT This project is an equipment which been fabricated for the principle purpose of producing heat energy for commercial use by burning solid fuel like briquette. The project which is the fabrication of briquette stove was made from preferentially selected engineering materials like mild steels of different gauge member and metallic rod.... Continue Reading
     ABSTRACT In this project, three alternative design solutions were considered for the foldable cam – bed. The authors utilize the local materials (with cost consideration) for the components. The merits and demerits of each of the alternative with respect to the considered group were also discusses and the solutions of the alternatives that... Continue Reading
    REPORT ON ABSTRACT The construction of sieves system was carried out in the Engineering workshop, Institute of management and technology, Enugu. The aim of this project is to fabricate a sieve system, which is capable of separating solid particles of various sizes. The construction was carried out in order to... Continue Reading
    ABSTRACT In this project, three (3) alternative design solutions were considered for the camp-bed. The authors utilize the local raw materials (with cost consideration) for the comments. The merits and demerits of each of the alternative with respect to the considered grip were also discussed and the solutions of the alternatives that best... Continue Reading
    ABSTRACT Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet; precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel. The shelf is... Continue Reading
    ABSTRACT Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet. Precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel. The shelf is... Continue Reading
    ABSTRACT In this project, three alternative design solutions were considered for the foldable cam – bed. The authors utilize the local materials (with cost consideration) for the components. The merits and demerits of each of the alternative with respect to the considered group were also discusses and the solutions of the alternatives that best... Continue Reading
    ABSTRACT Bookshelf, a Mechanical arrangement of materials were documents are stored, it could be made with metal or wood. But this one is fabricated with metal. The type of metal used in the fabrication is mild steel and square baluters. The undismountable bookshelf which has five partitions and four compartment under went many process namely, the... Continue Reading