+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

CONSTRUCTION OF A MICROCONTROLLER BASED GATE

  • Type:Project
  • Pages:58
  • Format:Microsoft Word
(Electrical Engineering Project Topics & Materials)
ABSTRACT
Microcontroller based automate controller is a project design of a system that is used in operating a gate automatically. The system opens the gate automatically when a human being or car is about to enter a compound or exit a compound. The system works by sensing the light rays from the head lamp of the vehicle. The light ray is sensed and signal is used in operating the gate. Different blocks of circuit are put together to ensure that the system works perfectly as desired. The blocks include; the power supply unit, the control unit, the sensor unit, and drive unit. The power supply unit powers on the entire system, it supplies appropriate dc signal to where it is needed. The supply unit is made up of a 12volts step down transformer, a bridge rectifier circuit, a filter capacitor and a voltage regulator IC. The control unit receives signal from the sensor section to control the remaining part of the system. The control section is the logical part of the system and decides the state of the entire system depending on the signal from the sensor unit. The control section carries its operation with use of a microcontroller ATMEL89S52. The sensor unit receives signals from the headlamp of the vehicle or the human being and sends signals to indicate that a human being or car is present. This is achieved with the use a light dependent resistors. The drive unit is a DC motor which carries the gate to a specific direction as indicated by the microcontroller.

TABLE OF CONTENTS

Title page - - - - - - - - - - - i
Approval page - - - - - - - - - -ii
Dedication - - - - - - - - - - -iii
Acknowledgement - - - - - - - -iv
Abstract - - - - - - - - - - - -v
Table of contents - - - - - - - - -vi
List of figures - - - - - - - - - - -x
List of tables - - - - - - - - - - -xii

CHAPTER ONE
1.0 INTRODUCTION - - - - - - - - -1
1.1 BACKGROUND OF THE PROJECT - - - - -1
1.2 AIMS AND OBJECTIVE OF THE PROJECT - - - -2
1.3 SCOPE OF THE PROJECT - - - - - - -2
1.4 DEFINITION OF TERMS - - - - - - - 4
1.5 PROJECT REPORT ORGANIZATION - - - - -4

CHAPTER TWO
2.0 LITERATURE REVIEW - - - - - - - -6
2.1 INTRODUCTION - - - - - -- - - -6
2.2 REVIEW OF SENSORS -- - - - - - - -8
2.3 REVIEW OF THE ATMEL AT89S52 MICROCONTROLLER - -10
2.4 REVIEW OF DOOR CONTROL - - - - - -12

CHAPTER THREE
3.0 SYSTEM ANALYSIS - - - - - - - - 14
3.1: INTRODUCTION - - - - - - - - - 14
3.2: THE POWER SUPPLY UNIT: - - - - - - - - 15
3.3: THE CONTROL SECTION: - -- - - - - - 16
3.4: THE SENSOR UNIT: - - - - - - - - - - - - -17
3.5: THE GATE DRIVE UNIT - - - - - - - - - 17
3.6: DESCRIPTION OF COMPONENTS USED IN THE DESIGN - 19
3.6.1: Voltage Regulators - - - - - - - - 19
3.6.2: Transistors - - - - - - - - - 21
3.6.2.1: Types of Transistor - - - - - - - 22
3.6.2.2: Transistor currents - - - - - - - - 23
3.6.3: Light Dependent Resistor (LDR) - - -- - - 26
3.6.4: Electromechanical Relay -- - - - - - - 26
3.6.5: Diodes - -- - - - - - - - - 27
3.6.6: Microcontroller unit: - - - - - - - - 30
3.6.6.1: Features of AT89S52 - - - - - - - 31
3.6.6.2: Pin description - - - - - - - - 34
3.7: SYSTEM SPECIFICATION - - - - - - - 38

CHAPTER FOUR
4.0 CONSTRUCTION APPROACH, CONSTRUCTION STEPS AND
EVALUATION - - - - - - - - - - 40
4.1 CONSTRUCTION APPROACH - - - - - - 40
4.2 CONSTRUCTION - - - -- - - - - 41
4.2.1 COMPONENT TESTING - - - - - - - 42
4.2.2 COMPONENT PLACING - - - - - - - 42
4.2.3 SOLDERING - - - - - - - - - 42
4.2.4 SYSTEM TESTING - - - - - - - - 43
4.2.5 CONSTRUCTION MATERIALS - -- - - - 43
4.3 TESTING EQUIPMENT - - - - - - - - 44
4.4 TESTING METHOD - -- - - - - - - 44
4.4.1 RESISTORS: - - - - - - - - - 44
4.4.2 CAPACITORS: - - - - - -- - - - 44
4.4.3 TRANSISTORS: - - - - - -- - - - 44
4.5 SYSTEM FLOWCHART - - - - - - - - 46
4.6 CIRCUIT DIAGRAM: - - - - - - - - 47
4.6.1 CIRCUIT DIAGRAM EXPLANATION - - - 48
4.7 EVALUATION - - - - - - - - - 48

CHAPTER FIVE
5.0 TEST RESULT, RECOMMENDATION AND CONCLUSION - -52
5.1 SYSTEM TESTING - - - - - - - - 52
5.2 SUMMARY - - - - - - - - - - 52
5.3 RECOMMENDATION - - - -- - - - - 54
5.4 CONCLUSION - -- - - - - - - - 54
REFERENCES - - -- - - - - - - - 56
APPENDIX - - - - - - - - - - 58
CONSTRUCTION OF A MICROCONTROLLER BASED GATE

Share This

Details

Type Project
Department Electrical Engineering
Project ID ELE0198
Price ₦3,000 ($9)
No of Pages 58 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Electrical Engineering
    Project ID ELE0198
    Price ₦3,000 ($9)
    No of Pages 58 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The project is based on Construction of microcontroller vehicle speed alarm system which automatically warns the driver by activating a panic alarm which is triggered on when the driver exceeds the speed limit set in the system which also stops the alarm when the speed is reduced below the set speed limit. A speedometer system is used to... Continue Reading
    ABSTRACT The project is based on Construction of microcontroller vehicle speed alarm system which automatically warns the driver by activating a panic alarm which is triggered on when the driver exceeds the speed limit set in the system which also stops the alarm when the speed is reduced... Continue Reading
    ABSTRACT This project shows the construction of a microcontroller based security door using smart card. It is aimed towards programming the microcontroller to control the hardware in sliding door. The system consists of a microcontroller 89S52 which sends a signal to the multiplexers on insertion of the smart card in the card slot. The... Continue Reading
    ABSTRACT T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the pedestrians a right of the way at intervals rather than being struck down when in a... Continue Reading
    ABSTRACT T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the... Continue Reading
    ABSTRACT T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the... Continue Reading
    ABSTRACT The need for a remote control system that can control domestic appliances and various lighting points and sockets has often been a concern for uses at times uses find it inconvenient and time they are leaving the house for work it has also often led to damage of appliances due to the fact that an appliances was not timed off before... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1                             OBJECTIVE OF PROJECT The need for a remote control alert system that can control domestic appliances and various lighting points and sockets has often been a concern for users. At times users find it inconvenient and time consuming to go around turning their... Continue Reading
    Abstract               During the invention of security system alarms, in the early 80s technology of system shadow which involves lighten and sensing of objects was at that age found during their experiments using a special material know as light dependent resistor which its family lies in the resistance serials. The development of... Continue Reading
    ABSTRACT Most industrial and commercial processes are dependent on electrical power. Power failure or outage in general does not promote development in public and private sectors. The investors do not feel secure to come into a country with constant or frequent power failure. This limits the development of industries.In addition there are... Continue Reading