+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

PROJECT ON CONSTRUCTION AND TESTING OF A LIGHT DIMMER SWITCH

  • Type:Project
  • Pages:15
  • Format:Microsoft Word
(Medical and Health Science Project Topics & Materials)

This project (light Dimmer Switch) is base on adjusting the voltage which gets to the lamp. The project use an alternating current as an input at the rate 240v from the socket outlet. The circuit is mainly used to control the desired brightness of the lamp of 100watts, by limiting the flow of current through the lamp by their equivalent resistance, which the capacitor used to store same charges when the variable resistor is varied. The project dimmer switch can be used in so many places. 

 

 

 


 

TABLE OF CONTENT

 

TITLE PAGE. i

DECLARATION.. ii

CERTIFICATION.. iii

DEDICATION.. iv

ACKNOWLEDGEMENT. v

ABSTRACT. vi

TABLE OF CONTENT. vii

CHAPTER ONE

1.0     INTRODUCTION.. 1

1.1     AIMS AND OBJECTIVES. 1

1.2     MOTIVATION AND SIGNIFICANCE. 2

1.3     SCOPE AND LIMITATION.. 2

1.4     METHOLOGY. 3

CHAPTER TWO

2.0     LITERATURE REVIEW... 4

2.1     PREVIOUS CONTROL DIMMER SWITCH.. 4

2.2     OVER VIEW OF THYRISTOR.. 5

2.3         OVER VIEW OF CAPACITOR.. 6

2.4     OVER VIEW OF RESISTOR. 6

CHAPTER THREE

3.1     PRINCIPLE OF OPERATION.. 7

3.2     DESIGN ANALYSIS AND CALCULATION.. 8

CHAPTER FOUR

4.0     CONSTRUCTION, TESTING AND PACKAGING.. 10

4.1     TESTING OF LIGHT DIMMER SWITCH.. 10

4.2.        PACKAGING.. 10

4.3     LIST OF COMPONENTS. 11

CHAPTER FIVE

5.0      CONCLUSION, PROBLEMS  ENCOUNTERED AND RECOMMENDATIONS. 12

5.1     CONCLUSION.. 12

5.2     PROBLEM ENCOUNTERED.. 12

5.3     RECOMMENDATION.. 12

REFERENCE. 14

PROJECT ON CONSTRUCTION AND TESTING OF A LIGHT DIMMER SWITCH

Share This

Details

Type Project
Department Medical and Health Science
Project ID MHS0115
Price ₦3,000 ($9)
No of Pages 15 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Medical and Health Science
    Project ID MHS0115
    Price ₦3,000 ($9)
    No of Pages 15 Pages
    Format Microsoft Word

    Related Works

    CHAPTER ONE 1.0.   INTRODUCTION 1.1.   GENERAL DESCRIPTION OF THE PROJECT Industrial electronics has turned the whole world into a global village. One of the most indispensable aspects of these phenomena is automation, which forms the nucleus of the present day electronics technology. Considering the milestone, it was desired to make the... Continue Reading
    ABSTRACT As the zeal for change over on public power supply and stand- by generator increases; Engineers have researched deeply into the different ways and methods of achieving power changeover both manual and automatic types. It may no be considered as serious issue in some places where supply is up to 90% constant or where intermittent outage... Continue Reading
    TABLE OF CONTENT: CHAPTER ONE INTRODUCTION 1.1 OBJECTIVE OF PROJECT 1.2 JUSTIFICATION OF PROJECT 1.3 SCOPE OF DIAGRAMS IN PROJECT 1.4 BLOCK DIAGRAM OF PROJECT 1.5 PROJECT REPORT ORGANIZATION CHAPTER TWO LITERATURE REVIEW 2.1 REVIEW OF REMOTE CONTROL SYSTEMS 2.2 DESCRIPTION OF PROJECT 2.3 USE OF PROJECT CHAPTER THREE METHODOLOGY 3.1 INFORMATION... Continue Reading
    ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading
    ABSTRACT A 1.05 cubic metre capacity storage facility which is to increase the shelf life of stored vegetables as designed fabricated and tested. The equipment operates on the principle of evaporative cooling and increasing the relative humidity of the interior of the equipment. The door and the back wall were of particle board of 12mm thickness... Continue Reading
    ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and... Continue Reading
    ABSTRACT This project work deals on the design and construction of an automatic power changeover that will change/transfer control from MAINS to Gen set and can switch ON/OFF the Gen automatically. The system integrates phase selector in MAINS and changeover to Gen. It is designed in several blocks all combined to from one functional unit. A +5v... Continue Reading
    ABSTRACT This project work deals on the design and construction of an automatic power changeover that will change/transfer control from MAINS to Gen set and can switch ON/OFF the Gen automatically. The system integrates phase selector in MAINS and changeover to Gen. It is designed in several blocks all combined to from one functional unit. A +5v... Continue Reading
    DESIGN AND CONSTRUCTION OF AN AUTOMATIC CHANGE OVER SWITCH WITH GENERATOR CUT OFF AND STARTER ABSTRACT Power supply in Nigeria and most developing countries of the world is anything but stable. This has adverse effects on the consumers of the electricity and the equipments that are operated from the mains sources of electricity supply in these... Continue Reading
    ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading