CONSTRUCTION OF OFFICE TABLE AND CHAIRS

  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0211
  • Access Fee: ₦5,000 ($14)
  • Pages: 58 Pages
  • Format: Microsoft Word
  • Views: 988
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT

The aim of this project was to construct one office table and four chairs.
In the course of this project the length of plank used was 12” and we used about 4 number (mahogany) of 1” thickness, ¾ plywood of 1 sheet of 1” thickness, as well as ¼” plywood of ½  and glue 1 tin wenner 1 rod, foam ½ sheet.  Fabrics 4 years, spraying materials and 21b of nail were utilized to effect the  construction of office table and chairs.
The materials were marked out to the required sizes, cut, folded, fited, assembled, nail, mort iced and then spraying it finally to prevent corrosion attack 
There are the necessary constructional procedure steps adopted in the project.  The accuracy and precision with which the construction steps and consequently, the assemblage of the component parts greatly enhanced our aim of constructing a suitable equipment for use of one table and four chairs.
The aim of constructing the table and the chair is to enable chemical Engineering department as future Engineer to know and also learn how to construct an office table or chairs and the essence of it.  The cost of production of the office table and chairs as at 7th August, 2005 is N21,000.00

TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
LETTER OF TRANSMITTAL 
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENTS

CHAPTER ONE
1.1 Introduction

CHAPTER TWO
2.0 Literature Survey
2.1 Definition and types of table and chairs
2.2 Chemistry and structure of timber and wood
2.3 Chemical components of wood
2.4 Categories of wood
2.5 Categories of wood
2.6 Uses of wood
2.7 Structure of timber
2.8 Wood pattern making
2.9 Pattern makers tools
2.10Materials
2.11Dowel pins
2.12Types of patterns
2.13Core points and core boxes
2.14Timber and wood carving
2.15Toothed cutting tools
2.16Foaming or steel square.

CHAPTER THREE
3.0 Constructional procedure
3.1 Cutting list
3.2 Sketching and Drawing
3.3 Cutting
3.4 Assembling
3.5 Sand papering
3.6 Paderded

CHAPTER FOUR
4.0 Discussion
4.1 Conclusion
4.2 Recommendation
4.3 Appendices
4.4 References 

CONSTRUCTION OF OFFICE TABLE AND CHAIRS
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0211
  • Access Fee: ₦5,000 ($14)
  • Pages: 58 Pages
  • Format: Microsoft Word
  • Views: 988
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0211
    Fee ₦5,000 ($14)
    No of Pages 58 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT A mould can generally be defined as a pattern constructed for the production of the same shape and size. The constructional material differs from one operation to another. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    ABSTRACT A mould can generally be defined as a pattern constructed for the production of the same shape and size. The constructional material differs from one operation to another. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    ABSTRACT A table top liquid-liquid extraction unit was constructed. The project also involved the repair and servicing of peristaltic suction pump, by painting it, replacing the connecting cord to the power supply, refilling of the work out suction plates, teeth and general servicing of the equipment. The glass absorption columns were provided as... Continue Reading
    ABSTRACT A table top liquid-liquid extraction unit was constructed.  The project also involved the repair and servicing of peristaltic suction pump, by painting it, replacing the connecting cord to the power supply, refilling of the work out suction plates, teeth and general servicing of the equipment.  The glass absorption columns were provided... Continue Reading
    ABSTRACT A mould can generally be defined as a pattern constructed for the production of the same shape and size. The constructional material differs from one operation to another. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
      ABSTRACT: This project design is simply used to display the items demanded by each customer on the table. Each table has four buttons for Rice, beans, amala and akpu, and each of the buttons are connected to the processor. The customers on every table presses the button with the label of the item he or she needed. Then, a screen in the... Continue Reading
    THE RELEVANCE OF NEW PRODUCT DEVELOPMENT ON ATTAINING MARKETING OBJETCIVE OF TABLE PRODUCERS IN ANAMBRA STATE. ( A CASE STUDY OF SELECTED TABLE WATER PRODUCERS) ABSTRACT This study was conducted to determine the relevant of new product development in attaining marketing objective of table water manufacturers in Anambra State . However, to achieve... Continue Reading
    SALES PROMOTION: A TOOL FOR ACHIEVING CUSTOMERS BRAND LOYALTY IN THE TABLE WATER INDUSTRY ( A CASE STUDY F VINUELA TABLE WATER IN UMUAHIA CAPITAL CITY). ABSTRACT This topic sales promotion: a tool for achieving customer brand loyalty in the table water industry was conducted to investigate the extent of relationship between effective sales... Continue Reading
    ABSTRACT The construction of soap cutting table, mould and cutters became inevitable as it’s importance in our industries and society could not be over emphasized. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    ABSTRACT The construction of soap cutting table, mould and cutters became inevitable as it’s importance in our industries and society could not be over emphasized. When one considers the money at hand, he decides whether to start from the primary production level or secondary... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us