CONSTRUCTION OF A PILOT MOTORIZED MIXER

  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0208
  • Access Fee: ₦5,000 ($14)
  • Pages: 44 Pages
  • Format: Microsoft Word
  • Views: 770
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT

A motorized mixer of 200 liters capacity was constructed to have the capability of mixing 200 liters of fluid during operation.
The construction of the mixer involves the preliminary measures and calculations on the surface area of the metal sheet.  Some basic workshop practices was carried out during the construction such as the marking out of the metal sheet, cutting of different sizes of the sheet, welding of the prints, assembling of the components parts and painting of the equipment.
The material used in the construction of the mixer is mainly of mid steel.  The mild steel was used for the construction due to its quality cost availability and characteristics.
The cost of constructing the motorized mixer was cheep due to the choice of material selected for the constructional project and it was finally painted with aluminum paint to protect it form corrosion.
The material dimension used in construction of the motorized mixer is as follows:
Length of vessel700mm
Diameter of vessel600mm
Length of shaft800mm
Surface area of plastic vessel1320000mm
Electric motor rating733.3v50/60HZ, 3728.5 watt 7000r pm

TABLE OF CONTENT
Title page
Letter of transmittal
Acknowledgement
Dedication
Abstract
Table of content

CHAPTER ONE
1.0  INTRODUCTION
1.1  Problems encountered during mixing
1.2  Purpose of mixing

CHAPTER TWO
2.0  LITERATURE REVIEW
2.1  Theory of mixing
2.2  Types of mixers
2.3  Classes of impellers
2.4  Types of impellers
2.5  Other types of mixers
2.6  Criteria of mixer effectiveness
2.7  Application of mixers
2.8  Functions of impellers
2.9  Mechanism of a pilot motorized mixer Degree of mixing
2.10 Mixing rates
2.11 Selection of material
2.12 Steel for construction
2.13 Types of steel-in construction
2.14 Important properties of steel in construction
2.15 Protection of steel

CHAPTER THREE
3.0  Sequence of operation 
3.1  Analysis of cost
3.2  Operation of the motorized mixer

CHAPTER FOUR
4.0  Conclusion/Recommendation
4.1  Nomenclature
     References 

CONSTRUCTION OF A PILOT MOTORIZED MIXER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0208
  • Access Fee: ₦5,000 ($14)
  • Pages: 44 Pages
  • Format: Microsoft Word
  • Views: 770
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Chemical Engineering
    Project ID CNG0208
    Fee ₦5,000 ($14)
    No of Pages 44 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT The fabrication of the pilot motorized mixer in volved a preliminary computation of the durunsions of the galvanized steel used, marketing out cutting out to sizes folding, welding, assembling and painting. The dimensions of the motorized mixer are as follows: The vessel is of 300min in diameter and 450mm... Continue Reading
    CONSTRUCTION OF A PILOT MOTORISED MIXER A REPORT PRESENTED TO THE DEPARTMENT OF CHEMICAL ENGINEERING OF THE INSTITUTE OF MANAGEMENT AND TECHNOLOGY, ENUGU ABSTRACT A motorized mixer of 200 liters capacity was constructed to have the capability of mixing 200 liters of fluid during operation. The construction of the mixer involves the preliminary... Continue Reading
    ABSTRACT  The motorized cassava peeling machine is a type of cassava peeling method that is adopted to reduce drudgery. In cassava peeling operations. This method, unlike the manual peeling method which consumes a lot of human power with subsequent low output produces or peels a large amount of cassava tubers within a small specific of time and... Continue Reading
    ABSTRACT The motorized cassava peeling machine is a type of cassava peeling method that is adopted to reduce drudgery. In cassava peeling operations. This method, unlike the manual peeling method which consumes a lot of human power with subsequent low output produces or peels a large amount of cassava tubers within a small specific of time and... Continue Reading
    ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding, body... Continue Reading
    ABSTRACT Industrial mixer is equipment designed to carryout operation involved the combination of two or more substance to achieve a uniform product. The method of fabrication of this mixer involves a preliminary computation of the dimensions of the standard which they will be used in marketing out cutting, out to... Continue Reading
    ABSTRACT The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu. The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which... Continue Reading
      ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension  of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding,... Continue Reading
    ABSTRACT The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu. The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which... Continue Reading
    ABSTRACT A paint mixer is defined as a pattern constructed for the production (mixing) of paint manually.  The method of fabrication of the paint mixer involved a preliminary computation of the dimensions of the standard mixer in relation to the dimension of the reacting vessel in which they will be used in marking out, cutting out to sizes,... Continue Reading
    Call Us
    Get this work
    whatsappWhatsApp Us