+234 813 0686 500
+234 809 3423 853
info@grossarchive.com

DESIGN AND CONSTRUCTION OF AN INTELLIGENT 250 VOLTS BATTERY CHARGER WITH MICRO PROCESSOR USING SEVEN SEGMENT DISPLAY

  • Type:Project
  • Chapters:5
  • Pages:37
  • Format:Microsoft Word
(Engineering Project Topics & Materials)

Design And Construction Of An Intelligent 250 Volts Battery Charger With Micro Processor Using Seven Segment Display

 




TABLE OF CONTENTS

Title page                                             i

Certification page                                      ii

Dedication                                                 iii

Acknowledgement                                      iv

Abstract                                                    v

Table of content                                         vi-vii

CHAPTER ONE

Introduction                                             1

What is Battery Charger                             1

What is an Intelligent Battery Charger          1

Other Types of Battery Charger                   2-3

CHAPTER TWO

Literature Review                                      4-5

CHAPTER THREE

Component     Description                          6

Micro Controller                                        6-14

Resistor                                                   14-16

Transistor                                                16

Seven Segment Display                             17-18

Capacitor                                                        18-20

Transformer                                             21

Diode                                                      21-22

CHAPTER FOUR

Principle of Operation                                23-27

Circuit Diagram                                         28

Component List                                        29

CHAPTER FIVE

Conclusion                                               30

Recommendations                                    31

References                                               32


CHAPTER ONE.

INTRODUCTION

WHAT IS A BATTERY CHARGER: A battery charger is a device used to put energy into a secondary cell or rechargeable battery. By forcing on electric current through it.

The charge current depends upon the technology and capacity of the battery being charged. For example, the current that should be applied to recharge a 12v car battery will be very different from the current for a mobile phone battery.

WHAT IS AN INTELLIGENT BATTERY CHARGER: This is a battery charger whose output current depends upon the battery’s state. An intelligent charger may monitor  the battery’s voltage, temperature and/ or time under charge to determine the optimum charge current at that instant. Charging is terminated when a combination of the voltage, temperature and/or time indicates that the battery is fully charged.

OTHER TYPE OF BATTERY CHARGERS

1.   SIMPLE  BATTERY CHARGER: A simple charger works by connecting a constant dc power source to the battery being charged. A simple charger does not alter its output based on time or the charge on the battery. This simplicity means that a simple charger is inexpensive but there is a trade off in quality.

2.   TRICKLE BATTERY CHARGER:  A trickle charger is a kind of simple charger that charges the battery slowly, at the self-discharge rate. A trickle charger is the slowest kind of battery charger.

3.   TIMER-BASED BATTERY CHARGER: The output of timer charger is terminated after a predetermined time. Timer chargers were the most common type for high-capacity Ni-Cd cells in the late 1990s

4.   FAST BATTERY CHARGER: fast chargers make use of control circuitry in the batteries being charged to rapidly charge the batteries without damaging the cells element. Most such chargers have a cooling fan to help keep the temperature of the cells under control.

5.   PULSE BATTERY CHARGER: some charger use pulse technology in       which a pulse is fed to the battery. This DC pulse has a strictly controlled rise time, pulse width, pulse repetitive rate (frequency) and amplitude. This technology is used to work with any size, voltage, capacity or chemistry of batteries including automotive and valve-regulated batteries. .

6.   INDUCTIVE BATTERY CHARGER: Inductive battery chargers use electromagnetic induction to charge batteries. A charging station sends electromagnetic energy through inductive coupling to an electrical device which stores the energy in the batteries

7.      USB-BASED BATTERY CHARGER: Since the universal serial bus specification provides for a five-volt power supply, it is possible to use a USB cable as a power source for recharging batteries. 

DESIGN AND CONSTRUCTION OF AN INTELLIGENT 250 VOLTS BATTERY CHARGER WITH MICRO PROCESSOR USING SEVEN SEGMENT DISPLAY

Share This

Details

Type Project
Department Engineering
Project ID EGR0003
Price ₦3,000 ($9)
Chapters 5 Chapters
No of Pages 37 Pages
Format Microsoft Word

500
Leave a comment...

    Details

    Type Project
    Department Engineering
    Project ID EGR0003
    Price ₦3,000 ($9)
    Chapters 5 Chapters
    No of Pages 37 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT           A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    ABSTRACT This project presents the design and construction of a battery charger. A battery charger is an electrical/electronic device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.  The system  consists of a step down transformer, an AC to DC converter and a DC voltage regulator. The... Continue Reading
    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
    ABSTRACT This project which comprise of many chapters that deals extensively with designs and construction of battery charger with auto-cut off which is capable of charging a 12 volts battery. In this construction research, designs was carried out which historic research was used to break down and evaluate to a low level understating of what an... Continue Reading
      ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading
    Chapter one INTRODUCTION 1.1     Background of the study Electronic digital display system as used in this reports refers to a sign that uses electronic hardware and software to display its copy, messages or images. Also, a sign utilizing a fixed light source to provide a message  in text, images pictures, and / or symbols that may appear to... Continue Reading
    INTRODUCTION The purpose of this project is to produce a narrative description of the design and construction of a microcontroller based dot matrix advert display. Firstly computer aided design is the modeling of physical system on Computers allowing both interactive and automatic analysis of design variant and the expression of design in a form... Continue Reading
    ABSTRACT This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work under the strict supervisor of Engr K.C Ugwu.  I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this... Continue Reading
    DEDICATION We dedicate this project work to Almighty God, the source of all knowledge, wisdom and understanding, for being there for us throughout the period of our study and to our lovely parents, Mr. and Mrs. Abido, and Sir & Lady Christopher Korugbo for their parental care, who has always been our inspiration. ACKNOWLEDGEMENTS Thanks to God... Continue Reading