Explore Project Topics on: INSTALLATION OF FOUR BEDROOM FLAT

ABSTRACT This project present a practical demonstration of how to carryout the wiring of a two bedroom bungalow, using PVC conduit system. In recent times surface wiring is gradually giving way to conduit wiring where much of the cable are concealed. PVC pipes are used because of it cost friendliness, compared to metal conduit. In carryout this... Continue Reading

ABSTRACT This project present a practical demonstration of how to carryout the wiring of a two bedroom bungalow, using PVC conduit system. In recent times surface wiring is gradually giving way to conduit wiring where much of the cable are concealed. PVC pipes are used because of it cost friendliness, compared to metal conduit. In carryout this... Continue Reading

ABSTRACT The fabrication of the solar dryer was successful and test were carried out for various performance comparisons such as No-load and Load performance of the dryer and direct sun drying comparison and noticeable differences was noticed in the final moisture content such that the maximum temperature recorded in the drying chamber and solar... Continue Reading

ABSTRACT The fabrication of the solar dryer was successful and test were carried out for various performance comparisons such as No-load and Load performance of the dryer and direct sun drying comparison and noticeable differences was noticed in the final moisture content such that the maximum temperature recorded in the drying chamber and solar... Continue Reading

PREFACE In structural detailing, the project is initiated by the structural engineer. The architectural drawings are prepared by the architect to the required scale and specification given to him by the client. The structural engineer designs the structural frame work of the building and specification required such as slab, beam, column and... Continue Reading

ABSTRACT This research work focuses on the development of Iso-safety design charts for flexural design of flat slabs at predefined reliability levels in accordance with Eurocode 2 (2004) design criteria. Constitutive models for reinforcing steel and concrete were selected in accordance with the Eurocode 2 design requirements and subsequently the... Continue Reading

ABSTRACT This work investigated the variation of top loss heat transfer coefficient with the emittance of the absorber plate, the collector tilt angle and air gap spacing between the absorber plate and the cover plate. The effects of the emittance of the absorber plate, the collector tilt angle and air gap spacing between the plate and the cover... Continue Reading

ABSTRACT This work investigated the variation of top loss heat transfer coefficient with the emittance of the absorber plate, the collector tilt angle and air gap spacing between the absorber plate and the cover plate. The effects of the emittance of the absorber plate, the collector tilt angle and air gap spacing between the plate and the cover... Continue Reading

ABSTRACT Renovation, a term most commonly associated with buildings is known to be the act or process of improving the existing condition of a broken, damaged or outdated structure. It is the process of restoring to a good condition or making new again a building structure currently in a bad state. The concept of renovation as it relates to... Continue Reading

STRUCTURAL DETAILING IN REINFORCED CONCRETE OF A THREE BEDROOM DETACH DUPLEX, IN AZUIYIOKWU ABAKALIKI EBONYI STATE PREFACE In structural detailing, the project is initiated by the structural engineer. The architectural drawings are prepared by the architect to the required scale and specification given to him by the client. The structural engineer... Continue Reading

STRUCTURAL DETAILING IN REINFORCED CONCRETE OF A THREE BEDROOM DETACH DUPLEX, IN AZUIYIOKWU ABAKALIKI EBONYI STATE PREFACE In structural detailing, the project is initiated by the structural engineer. The architectural drawings are prepared by the architect to the required scale and specification given to him by the client. The structural engineer... Continue Reading

ABSTRACT The purpose of this work is to use the energy approach in the form of direct variational principle (Rayleigh-Ritz method) for buckling analysis of thin rectangular plates with various boundary conditions using Taylor series shape functions. To do this, thin rectangular flat plate of various boundary conditions with three dimensions Ly, Lx... Continue Reading

ABSTRACT The purpose of this work is to use the energy approach in the form of direct variational principle (Rayleigh-Ritz method) for buckling analysis of thin rectangular plates with various boundary conditions using Taylor series shape functions. To do this, thin rectangular flat plate of various boundary conditions with three dimensions Ly, Lx... Continue Reading

  CHAPTER ONE 1.0 INTRODUCTION 1.1 BACKGROUND OF STUDY Safety is an essential component of transportation engineering. The safety of road transportation involves many factors including driver skills, roadway characteristics, vehicle conditions, and weather. In addition to crash causation, the identification of hazards that may increase severity... Continue Reading

EFFECT OF FRAUD MANAGEMENT ON A SURVIVAL OF A COMPANY (A CASE STUDY OF FIRST BANK NIGERIA PLC, UGHELLI BRANCH) ABSTRACT This topic is on “Effect of Fraud Management on a Survival of a Company” with special reference to First Bank Nigeria Plc. Ughelli branch. Indeed, fraud which have been a feature of Nigeria society today has cause a lot of... Continue Reading

ABSTRACT Researchers suggest that the amount of sunlight that strikes the Earth's surface in an hour and a half is enough to handle the entire world's energy consumption for a full year. Solar power system is one of the best renewable energy technologies which is not only cost effective but environment friendly as well.This study aimed at... Continue Reading

ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading

ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective... Continue Reading

ABSTRACT The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller.... Continue Reading

ABSTRACT A mega filling station can be described from its name –MEGA; which means larger in size. This implies that mega filling station is a large-scale fuel station outlets where fuels of various forms are sold. A typical example is the NNPC MEGA FILLING STATION in... Continue Reading

Abstract The advent of Global Navigation Satellite Systems (GNSS) in space technology has tremendously improved the methods of positioning and navigation. Countries are now adopting the continuous observation and measurements using a network of GNSS receivers called Continuously Operating Reference Stations (CORS) as the standard. Hence, the study... Continue Reading

Abstract The advent of Global Navigation Satellite Systems (GNSS) in space technology has tremendously improved the methods of positioning and navigation. Countries are now adopting the continuous observation and measurements using a network of GNSS receivers called Continuously Operating Reference Stations (CORS) as the standard. Hence, the study... Continue Reading

ACCOUNTING IMPLICATION OF COMPUTER INSTALLATION (A CASE STUDY OF UNITED BANK FOR AFRICA (UBA PLC) ABSTRACT The contribution of the banking industry to the economic development of any nation cannot be over-emphasized. Computers have also contributed greatly to ease the functions performed by this industries in trying to meet its economic... Continue Reading

ABSTRACT The study sought to determine the safety skills required by technical college electrical installation students in handling equipment. The study was carried out in Plateau and Kaduna States. A survey research design was employed for the study. The population for the study was 80 comprising of 39 electrical installation teachers and 41... Continue Reading

Abstract The study was carried out to determine the skills required by graduates of technical colleges for self-employment in electrical installation and maintenance works in Enugu State. A survey research design was adopted for the study. The population for the study was 35 respondents comprised of teachers of electrical installation and... Continue Reading

ABSTRACT The study sought to determine the safety skills required by technical college electrical installation students in handling equipment. The study was carried out in Plateau and The Kaduna States. A survey research design was employed for the study. The population for the study was 80 comprising of 39 electrical installation teachers and 41... Continue Reading